Firmware download

ytliu

Ver:2018-07-05-95 Modification:
1. Increase keyboard support
2. Increase the trial cut (handwheel guide) function
3. Add file editing function

Key mapping description:

X-: LEFT ARROW(←)、Numeric keypad '4'
X+: RIGHT ARROW(→)、Numeric keypad '6'
Y-: DOWN ARROW(↓)、Numeric keypad '2'
Y+: UP ARROW(↑)、Numeric keypad '8'
Z-: PAGEDOWN、Numeric keypad '3'
Z+: PAGEUP、Numeric keypad '9'
A-: Numeric keypad '1'
A+: Numeric keypad '7'


the centering operation:F3(Used in conjunction with the MPG axis selection. Only when the MPG axis is selected as X or Y, the corresponding axis performs the centering operation.)
Goto Zero:F5、Numeric keypad '0'(Used in conjunction with the MPG axis selection. If the MPG axis is selected to be empty, the whole axis will be goto zero. If the MPG axis is selected as X, the X axis will be goto zero.)
Zero:F6、Numeric keypad 'DEL'(Used in conjunction with the MPG axis selection.If the MPG axis is selected to be empty, the whole axis will be zero. If the MPG axis is selected as X, the X axis will be zero.)
Home:F7(The first press enters the HOME mode. In the HOME mode, press again to perform full axis HOME, or press the corresponding axis selection key, the corresponding axis will perform HOME separately.)
HOME X-axis selection:'X'
HOME Y-axis selection:'Y'
HOME Z-axis selection:'Z'
HOME A-axis selection:'A'
PROBE:F8(The first press enters PROBE mode and presses again to perform the PROBE operation.)

Manual mode switching:F10、Numeric keypad '*'
Jog distance adjustment:Numeric keypad '5'
FRO adjustment:'F'、'8'
SRO adjustment:'S'、'9'
Coordinate system selection:'G'、'0'


START:SCROLL LOCK、Numeric keypad '-'
PAUSE: PAUSE BREAK、Numeric keypad '+'
TRCUT:F11、Numeric keypad 'ENTER'
Single-stage processing mode:F4(The single-segment mode can be switched while the system is idle. After starting the machining in single-segment mode, the system executes one line each time the start button is pressed.)

Focus TAB：F9、Numeric keypad '/'
Focus adjustment+:'+'
Focus adjustment-:'-'

Page switching:TAB、BACKSPACE
Track display：F12

Uninstall U disk: DELETE

luis

hola junto con saludar requiero información ya que soy nuevo en esto y tengo poco conocimiento en este controlador DDCS4 V3.1, e adquirido este controlador hace ya un mes y quise conectar los pulsadores auxiliares de star, pause y stop pero no me funcionan hay alguna configuración para activarlos? agradecería mucho que me ayudaran.

Kev0

Sorry said it the wrong way. I got a D-100 and there is no manual available.

Why this cant be compensated ? Sure it can.
I set the rampup in DDCSV to 0 wich results in a 0-10V in no time. (Spindle reacts the same way -> ramp slow)
As the spindle runs its ramping curve it just needs more time to reach the desired speed.
In order to have the right cutting speed set the DDCSV to wait a bit longer. Everything is working.

Would be nicer to change the spindle ramping map but this is not possible without a manual .

bolek

Hello all, I have ddcsv2.1 but on-screen say ddcs3v2.1 .I have it unused for a while. The old cutting toy went to the garbage because of the worn and parallel port. I made a new frame and decide to use ddcsv. All works great but don't have all limit switches I use a proximity sw. Working on the proper motor setup I decided to test run circle. Now I see every time the tool gets to the beginning of the circle the machine stop and waits for the controller to catch up. I try different G codes and screw with configuration. Now I know that I have to download  G codes into ddcsv. The problem is that I don't have the imperial measurement, no more, only metric. No matter if I change it in config it shaw in. but the value is in mm.
What did I do, help, please

Xyem_no_ctoly

Здравствуйте,если я хочу оставить свою прошивку на контроллере но нужно мне изменить язык интерфейса как мне поступить где и какой файл куда вставлять,заранее спасибо

Xartan

luis Posted at 2019-11-16 00:00
hola junto con saludar requiero información ya que soy nuevo en esto y tengo poco conocimiento en e ...

Hola !!

Quiero entender que ya lo arreglaste, pero te respondo por si alguien lo ve y le vale.

Creo que tu problema es que no has alimentado la entrada auxiliar IO con 24V (com+ y com-)

Saludos.

Wlod

Hello everyone!!
writes by google translator
because I am from Poland.
I have DDCSV1.1 with an update
2018-10-09-101
a serious problem with reading the hole code, e.g.
of these holes made, the contour is made normally and the other enters with a milling cutter without a contour at full depth.
I generate paths from mastercam x3. Regards and please help

peter

Please help me, I use the 2-axis ddcsv2.1 controller. when I load the program on usb. when you press and run, it will be "syntax check 817 and syntax check 1070 ...." and then stop. no  works at all

ytliu

Hi Stein,
First of all, I want to know if you have successfully upgraded. For example, if you upgrade using install(2019-06-10-111).zip, after the upgrade is successful, Ver:2010-06-10-111NOR will be displayed in the lower right corner of the screen.

Stein

Good afternoon, I am writing to you in the hope of your help. I bought a DDCSV2.1 controller on 4 axes, for me it was important, until I bought a rotary axis on the settings, I didn’t look at all that. Everything works, but when I started to set everything up, I noticed that I have no axis A in the settings and all the settings regarding it. The most important thing on the back of the sticker and on the connector is that on the controller 4 axes. on the display, connected to the output axis And another axis to find out if it works or not — works. Tell me what to do, they said you need to install another firmware, I tried the other firmware does not stand up, nothing changes. USB flash drive la together with the controller. I don’t understand anything, I tried everything. Yes, and even in the settings there is such a very first Top Parametrs item, so there’s nothing empty under it. Just a line with this phrase. I hope for your help. Thank you very much.

Palavan

Tell me please. When you download a file, you can not see the processing path, is it just me or everyone?
I would like to differentiate amongst what we will do on the file name you can not remember.
I have a machine for cutting foam (facade decoration, 2D processing)
Or what to change in the settings to see it?