Firmware download - DDCSV2.1 - Standalone CNC Motion Controller - Digital Dream Technology support
View: 35641|Reply: 84

Firmware download

[Copy Link]

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
Posted at 2018-7-11 18:06:19 | All floors |Read mode
Last edited by ytliu In 2018-7-11 18:10 Editor

Ver:2018-07-05-95 Modification:
1. Increase keyboard support
2. Increase the trial cut (handwheel guide) function
3. Add file editing function

Key mapping description:

X-: LEFT ARROW(←)、Numeric keypad '4'
X+: RIGHT ARROW(→)、Numeric keypad '6'
Y-: DOWN ARROW(↓)、Numeric keypad '2'
Y+: UP ARROW(↑)、Numeric keypad '8'
Z-: PAGEDOWN、Numeric keypad '3'
Z+: PAGEUP、Numeric keypad '9'
A-: Numeric keypad '1'
A+: Numeric keypad '7'


the centering operation:F3(Used in conjunction with the MPG axis selection. Only when the MPG axis is selected as X or Y, the corresponding axis performs the centering operation.)
Goto Zero:F5、Numeric keypad '0'(Used in conjunction with the MPG axis selection. If the MPG axis is selected to be empty, the whole axis will be goto zero. If the MPG axis is selected as X, the X axis will be goto zero.)
Zero:F6、Numeric keypad 'DEL'(Used in conjunction with the MPG axis selection.If the MPG axis is selected to be empty, the whole axis will be zero. If the MPG axis is selected as X, the X axis will be zero.)
Home:F7(The first press enters the HOME mode. In the HOME mode, press again to perform full axis HOME, or press the corresponding axis selection key, the corresponding axis will perform HOME separately.)
HOME X-axis selection:'X'
HOME Y-axis selection:'Y'
HOME Z-axis selection:'Z'
HOME A-axis selection:'A'
PROBE:F8(The first press enters PROBE mode and presses again to perform the PROBE operation.)

Manual mode switching:F10、Numeric keypad '*'
Jog distance adjustment:Numeric keypad '5'
FRO adjustment:'F'、'8'
SRO adjustment:'S'、'9'
Coordinate system selection:'G'、'0'


START:SCROLL LOCK、Numeric keypad '-'
PAUSE: PAUSE BREAK、Numeric keypad '+'
TRCUT:F11、Numeric keypad 'ENTER'
Single-stage processing mode:F4(The single-segment mode can be switched while the system is idle. After starting the machining in single-segment mode, the system executes one line each time the start button is pressed.)

Focus TAB:F9、Numeric keypad '/'
Focus adjustment+:'+'
Focus adjustment-:'-'

Page switching:TAB、BACKSPACE
Track display:F12

Uninstall U disk: DELETE

install.zip

574.89 KB, Down times: 700

Reply

Use props Report

0

Threads

1

Posts

14

Credits

Newbie Member

Rank: 1

Credits
14
Posted at 2019-11-16 00:00:27 | All floors
hola junto con saludar requiero información ya que soy nuevo en esto y tengo poco conocimiento en este controlador DDCS4 V3.1, e adquirido este controlador hace ya un mes y quise conectar los pulsadores auxiliares de star, pause y stop pero no me funcionan hay alguna configuración para activarlos? agradecería mucho que me ayudaran.
Reply Support 1 Opposition 0

Use props Report

0

Threads

5

Posts

28

Credits

Newbie Member

Rank: 1

Credits
28
Posted at 2018-10-18 14:20:35 | All floors
Sorry said it the wrong way. I got a D-100 and there is no manual available.

Why this cant be compensated ? Sure it can.
I set the rampup in DDCSV to 0 wich results in a 0-10V in no time. (Spindle reacts the same way -> ramp slow)
As the spindle runs its ramping curve it just needs more time to reach the desired speed.
In order to have the right cutting speed set the DDCSV to wait a bit longer. Everything is working.

Would be nicer to change the spindle ramping map but this is not possible without a manual .
Reply Support 0 Opposition 1

Use props Report

0

Threads

1

Posts

8

Credits

Newbie Member

Rank: 1

Credits
8
Posted at 2018-7-16 14:47:00 | All floors
That's great thank you! Now it would be great if the DRO information is sent out through the serial interface ;-)
Reply Support Opposition

Use props Report

0

Threads

1

Posts

4

Credits

Newbie Member

Rank: 1

Credits
4
Posted at 2018-7-19 17:50:33 | All floors
This Firmware work with DDCSV1.1 ?
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-7-19 23:09:25 | All floors
Thank you very much for improving the software, this wonderful controller.
Sorry for the bad english - I write through Google translator.
There is a problem with the usb keyboard. If, hold and hold the button for
moving any axis for a long time, after releasing the button, the axis continues to move.
It can be fixed?
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-7-20 08:24:18 | All floors
thossapit Posted at 2018-7-19 17:50
This Firmware work with DDCSV1.1 ?

yes
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-7-20 08:26:08 | All floors
Nikolay81 Posted at 2018-7-19 23:09
Thank you very much for improving the software, this wonderful controller.
Sorry for the bad english ...

sorry! I did not find the problem you described, try another usb keyboard
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-7-20 17:15:19 | All floors
ytliu Posted at 2018-7-20 08:26
sorry! I did not find the problem you described, try another usb keyboard

The problem occurs when the keyboard is connected directly, without a USB hub. But with the hub, the response speed for releasing the key is greater than on the controller itself. That is, with manual control from the USB keyboard, the axis does not stop very fast. Can I reduce the response time for releasing the keys?
Reply Support Opposition

Use props Report

1

Threads

12

Posts

869

Credits

Senior Member

Rank: 4

Credits
869
Posted at 2018-7-25 14:06:00 | All floors
Hello ytliu,

Are you planning to release DDCSV software as an open source?
A lots of other projects on the internet shows that open source software modified and improved by a big community of users gets better and better very fast. Additionally in that case anyone could modify for example a screen layout or functionality of the controller to their machine...

Regards
Lukasz
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-7-27 10:39:53 | All floors
Lukasz Posted at 2018-7-25 14:06
Hello ytliu,

Are you planning to release DDCSV software as an open source?

hi,Lukasz
Sorry, we have no plans for open source yet.
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-7-27 10:44:25 | All floors
Ver: 2018-07-27-97 Modification:
1. Increase Russian support,configure #1 (language setting) to 2 so that the Russian configuration file (rus) will be loaded at startup. The rus file in the current installation package is not in Russian. If necessary, please translate it yourself.

install(2018-07-27-97).zip

583.64 KB, Down times: 212

Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list