M150_DM500 Upgrade file download!!! - DM500 - Handheld 3-4 Axis CNC Moiton Contr - Digital Dream Technology support
View: 7890|Reply: 27

M150_DM500 Upgrade file download!!!

[Copy Link]

5

Threads

56

Posts

316

Credits

Super Moderator

Rank: 8Rank: 8

Credits
316
QQ
Posted at 2019-4-28 14:26:41 | All floors |Read mode
Last edited by enjoy_cnc In 2020-4-14 23:52 Editor

Ver: 2018-04-12-93H0918
1: Occasionally pop-up problem in the edit box in the dialog box
2:chs and eng 116-119 configuration error problem

Ver: 2018-04-12-93H1011
1: Feedrate override is effective for both G01 and G00

Ver: 2018-04-12-93H1026
1: Increase 238 parameters IO filter time unit is ms, that is, IO scan time [Supported by FPGA version 01 or higher]
2: Add the hardware ID number and FPGA version information in the lower right corner of the main interface, for example ID: 9d8322b6f5106490_01 indicates that the hardware ID is: 9d8322b6f5106490 FPGA version is 01

Ver: 2018-04-12-93H1117
1: Soft limit will not overshoot

Ver: 2018-04-12-93H1120
1: Increase parameter No. 105, A-axis rotation characteristic. If set to rotary axis, the A-axis is completed within one circle of the workpiece and the excess mechanical coordinates are cleared.


Ver: 2018-04-12-93H1122
1: After turning on the A-axis rotation characteristic, the specified line machining and the near-point machining A-axis can be positioned in one turn;


Ver: 2018-12-02 (93)
1: The output port is configurable;

Ver: 2018-12-12 (93)
1: Modify the tool setting method: Firstly obtain the mechanical position of each knife in the knife, and then clear it;
2: Increase tool library support;
3: Increase the operation in the middle

Ver: 2018-12-19 (93)
1: Modify the multi-axis manual at the same time and simultaneously release the occasional movement of an axis.


Ver: 2019-01-05 (93)
1: Increase the jog distance setting dialog box;
2: Increase the program to start the spindle automatic start setting, and automatically close the spindle setting when the program ends;
3: Increase the boot-back mechanical zero prompt;
4: Check whether to return to zero before running the program;
5: The parameters are divided into user parameters and vendor parameters (admin password entry) can be classified according to the manufacturer;
6: Increase the automatic processing of the specified line processing;
7: The spindle speed can be adjusted during machining;
8: Increase the floating tool setting and fixed tool setting. The floating tool setting should be set to the thickness (positive value). The fixed tool setting tool thickness is automatically set.
9: The switch button can be configured according to the user's cycle options;

Ver: 2019-01-07 (93)
1: The visitor can unlock the password;

Ver: 2019-01-08 (93)
1: Remove the manual magnification display, and the manual override is combined with the feedrate override;
2: Modify the time calculation error after the installment is unlocked;



Ver: 2019-01-16 (93)
1: Support V1.2 version registration machine


Ver: 2019-02-21 (93)
1: increase the common offset of each axis
2: Modify the coordinate conversion method of the tool, the thickness of the tool is positive: the tool is higher than the machined surface

Ver: 2019-03-04 (93)
1: Fixed the problem of returning only Z when all the workpieces were zero.




Ver: 2019-03-12 (93)
1: prompt to return to mechanical zero after power-on reset


Ver: 2019-03-13 (93)
1: Corrected the abnormality of processing half an hour after the upgrade [2019-03-10] version;


Ver: 2019-03-23 ??(93)
1: Add the manual upgrade function, enter the parameter interface-advanced-system upgrade-restart, and copy the install folder to the root directory of the U disk before upgrading. Note that there is no more folder under the install folder.


Ver: 2019-04-05 (93)
1: Increase the tool setting parameter 150, fixed tool setting safety height (mechanical coordinate), fixed tool setting action flow: Z rises to the 150th parameter mechanical position, then moves XY to the 72, 73 mechanical position, then Z moves to 74 Mechanical position
2: Increase the search speed of the No. 151 tool setting signal;
3: Spindle multi-speed is compatible with Weihong pirate card mode (3+0);

Ver: 2019-04-23 (93)

1: Automatic parameter increase No. 152 Parameter: Near point comparison error Value range: 0.5-100mm, used to set the comparison error in the near-point machining during advanced machining.
The smaller the setting, the more accurate the positioning (applicable to the relief file). If the processing is a long line segment, the smaller the setting may not be searched. It is recommended to set this parameter to be large.
Not suitable for multi-layer machining, comparison principle: only compare whether the XY position is at the nearest point.

Ver: 2019-05-07 (93)

1: Modify the inching dialog box, the common offset dialog box, and the parameter dialog box entry mode to increase the previous data display.


Ver: 2019-05-30 (93)
1: Increase the 174 and 180 parameters. The buttons in continuous manual mode can be set separately by short-stroke distance.
? The inching distance in the inching mode remains the same.


Ver: 2019-06-06 (93)




1: Fix bugs in password modification for super administrators



Ver: 2019-06-18 (93)

1: Increase 239-245 output port number configuration parameters by default;
2: Add 461-468 input port number configuration parameters by default;
3: When the parameter interface is exited, the parameter number memory function is added, and the parameter interface is automatically positioned next time;
4: After the start processing is started, the focus is automatically switched to the "feedrate override", and the focus is automatically invalid after exiting the machining;
5: The switching focus is automatically disabled after the reset button is added;
6: Resolve the pause problem in the continuous movement of the A-axis after the setting soft limit is valid;
7: Solving the problem that the pulse distance is very short when the inching distance is short, causing manual movement;
8: Automatically limit the positive limit of the Z axis by increasing the total return to the workpiece zero mode;
9: Increase the information bar on the right side of the main interface.


Ver: 2019-06-19 (93)

1: Increase parameter 469 "Processing status display mode" percentage or remaining time
2: In the processing information bar on the right side of the main interface, increase the “remaining time” display;
3: Library file modification: all the return to workpiece zero process is changed to: when the current position of the Z axis is higher than the safe height, the last step Z axis

Do not perform the safe height action.


Ver: 2019-06-24 (93)

1: Pressing the “Spindle start/stop” button during processing is invalid.



Ver: 2019-07-23 (93)

1: Increase the metric system switching function, the parameter is 115
2: Adjust the coordinate display layout of the main interface


Ver: 2019-07-25 (93)

1: After the file is finished, if the A axis is under the rotation characteristic, the coordinates are automatically converted to 0-360.

Ver: 2019-08-01 (93)

1: Modify the semi-arc R programming overcut problem.


Ver: 2019-08-04 (93)
1: Increase the override adjustment delay, parameter 470: Feedrate override 1% change interval, in ns, default 20000ns
2: Correct the offset caused by the pulse equivalent calculation error when the A-axis is configured as the rotary axis.




Ver: 2019-09-05 (93)

1:175 parameter increases custom2 mode, rate-F-S;
2: Advanced machining increases, rectangular milling and other graphic programming;
3: Open tool library parameters and T.nc macro support;

Ver: 2019-10-12 (94)

1: The application software is compatible with the NAND memory version (memory size is 1G) and requires the latest hardware support;
2: In the file interface [Switch] button can be used to quickly switch U disk and local disk;
3: The file interface adds information such as the disk type and remaining space;
4: Parameter interface - advanced - parameter recovery adds two items, respectively, U disk recovery parameters and factory reset (default_setting);
5: File Interface - Advanced Add two operations: switch disk and fast copy operation;
6: The NAND memory version adds formatting operation. The specific operation is: long press the [spindle start/stop] button for 3 seconds;
7: Correct the XY-0 and ZA-0 button functions in the machine coordinate system;
8: Upgrade to version 94, modify the soft arc, the radius is too large, the program "fake death" problem;



Ver: 2019-11-02 (94)
1: Modify the library file back to the workpiece zero process, 1: Increase the safety height higher than the current value, and finally return to the safe height 2: Consider the Z positive soft limit position when the Z axis is lower than the safe height;
2: The tool magazine capacity parameter is open. If the T code is ignored, the tool magazine capacity of No. 90 can be set to 0.

Ver: 2019-11-19 (94)
1: Modify the problem that the X07 tool setting function is not executed


Ver: 2019-11-27 (94)
1: Adjust the magnification adjustment action. The magnification adjustment between% 0-10% will decrease by 1%. If it is greater than 10%, each time you press the key, it will decrease by 10%.


Ver: 2019-11-28 (94)
1: Add parameter 153, specify the line scanning method, fast positioning can shorten the scanning time

Ver: 2019-12-03 (94)
1: Add processing file .FNC format, internal system encryption and decryption function. Document requirements <8M

Ver: 2019-12-05 (94)
1: Added manual encryption operation on the handle interface to solve the problem of failure to decrypt the time-locked fkey file due to failure to recognize the boot U disk;
??? Proceed as follows:
?????????? Copy fkey to the root directory of the USB flash drive-insert the USB flash drive-enter the parameter interface-advanced-software registration-manual decryption and encryption


Ver: 2019-12-25 (94)
1: the manual tool change function is lifted;
2: Tool magazine support;


Ver: 2020-01-07 (94)
1: Add parameter 471, A axis protection speed during processing
2: Coordinate system parameters are added for double backup, which can be saved in separate files.

Upgrade steps:
1. Copy the upgrade folder install to the root directory of the USB flash drive;
2. Insert U disk and power off and restart;
3. The system will automatically search for the upgrade file to upgrade. During the upgrade, the interface will stay at the boot interface for about 10 S. Please wait patiently and do not power off;
4. Check if the version date of the main control interface is the same as that provided by the customer after booting;




M130-M150install20200107.rar

1.52 MB, Down times: 117

M130-M150install20200107

DM500install20200107.rar

1.23 MB, Down times: 309

DM500install20200107

Reply

Use props Report

5

Threads

56

Posts

316

Credits

Super Moderator

Rank: 8Rank: 8

Credits
316
QQ
 Author| Posted at 2019-12-28 22:27:47 | All floors
1. Copy the upgrade folder install to the root directory of the USB flash drive;
2. Insert U disk and power off and restart;
3. The system will automatically search for the upgrade file to upgrade. During the upgrade, the interface will stay at the boot interface for about 10 S. Please wait patiently and do not power off;
4. Check if the version date of the main control interface is the same as that provided by the customer after booting;
Reply Support 1 Opposition 0

Use props Report

5

Threads

56

Posts

316

Credits

Super Moderator

Rank: 8Rank: 8

Credits
316
QQ
 Author| Posted at 2019-9-19 23:25:21 | All floors


Ver: 2019-09-05 (93)
1:175 parameter increases custom2 mode, rate-F-S;
2: Advanced machining increases, rectangular milling and other graphic programming;
3: Open tool library parameters and T.nc macro support;


DM500 install 20190905.rar

1.21 MB, Down times: 124

20190905

Reply Support 1 Opposition 0

Use props Report

5

Threads

56

Posts

316

Credits

Super Moderator

Rank: 8Rank: 8

Credits
316
QQ
 Author| Posted at 2019-7-23 18:54:03 | All floors
Last edited by enjoy_cnc In 2019-7-23 19:18 Editor

Ver: 2018-04-12-93H0918
1: Occasionally pop-up problem in the edit box in the dialog box
2:chs and eng 116-119 configuration error problem

Ver: 2018-04-12-93H1011
1: Feedrate override is effective for both G01 and G00

Ver: 2018-04-12-93H1026
1: Increase 238 parameters IO filter time unit is ms, that is, IO scan time [Supported by FPGA version 01 or higher]
2: Add the hardware ID number and FPGA version information in the lower right corner of the main interface, for example ID: 9d8322b6f5106490_01 indicates that the hardware ID is: 9d8322b6f5106490 FPGA version is 01

Ver: 2018-04-12-93H1117
1: Soft limit will not overshoot

Ver: 2018-04-12-93H1120
1: Increase parameter No. 105, A-axis rotation characteristic. If set to rotary axis, the A-axis is completed within one circle of the workpiece and the excess mechanical coordinates are cleared.


Ver: 2018-04-12-93H1122
1: After turning on the A-axis rotation characteristic, the specified line machining and the near-point machining A-axis can be positioned in one turn;


Ver: 2018-12-02 (93)
1: The output port is configurable;

Ver: 2018-12-12 (93)
1: Modify the tool setting method: Firstly obtain the mechanical position of each knife in the knife, and then clear it;
2: Increase tool library support;
3: Increase the operation in the middle

Ver: 2018-12-19 (93)
1: Modify the multi-axis manual at the same time and simultaneously release the occasional movement of an axis.


Ver: 2019-01-05 (93)
1: Increase the jog distance setting dialog box;
2: Increase the program to start the spindle automatic start setting, and automatically close the spindle setting when the program ends;
3: Increase the boot-back mechanical zero prompt;
4: Check whether to return to zero before running the program;
5: The parameters are divided into user parameters and vendor parameters (admin password entry) can be classified according to the manufacturer;
6: Increase the automatic processing of the specified line processing;
7: The spindle speed can be adjusted during machining;
8: Increase the floating tool setting and fixed tool setting. The floating tool setting should be set to the thickness (positive value). The fixed tool setting tool thickness is automatically set.
9: The switch button can be configured according to the user's cycle options;

Ver: 2019-01-07 (93)
1: The visitor can unlock the password;

Ver: 2019-01-08 (93)
1: Remove the manual magnification display, and the manual override is combined with the feedrate override;
2: Modify the time calculation error after the installment is unlocked;



Ver: 2019-01-16 (93)
1: Support V1.2 version registration machine


Ver: 2019-02-21 (93)
1: increase the common offset of each axis
2: Modify the coordinate conversion method of the tool, the thickness of the tool is positive: the tool is higher than the machined surface

Ver: 2019-03-04 (93)
1: Fixed the problem of returning only Z when all the workpieces were zero.




Ver: 2019-03-12 (93)
1: prompt to return to mechanical zero after power-on reset


Ver: 2019-03-13 (93)
1: Corrected the abnormality of processing half an hour after the upgrade [2019-03-10] version;


Ver: 2019-03-23 ??(93)
1: Add the manual upgrade function, enter the parameter interface-advanced-system upgrade-restart, and copy the install folder to the root directory of the U disk before upgrading. Note that there is no more folder under the install folder.


Ver: 2019-04-05 (93)
1: Increase the tool setting parameter 150, fixed tool setting safety height (mechanical coordinate), fixed tool setting action flow: Z rises to the 150th parameter mechanical position, then moves XY to the 72, 73 mechanical position, then Z moves to 74 Mechanical position
2: Increase the search speed of the No. 151 tool setting signal;
3: Spindle multi-speed is compatible with Weihong pirate card mode (3+0);

Ver: 2019-04-23 (93)

1: Automatic parameter increase No. 152 Parameter: Near point comparison error Value range: 0.5-100mm, used to set the comparison error in the near-point machining during advanced machining.
The smaller the setting, the more accurate the positioning (applicable to the relief file). If the processing is a long line segment, the smaller the setting may not be searched. It is recommended to set this parameter to be large.
Not suitable for multi-layer machining, comparison principle: only compare whether the XY position is at the nearest point.

Ver: 2019-05-07 (93)

1: Modify the inching dialog box, the common offset dialog box, and the parameter dialog box entry mode to increase the previous data display.


Ver: 2019-05-30 (93)
1: Increase the 174 and 180 parameters. The buttons in continuous manual mode can be set separately by short-stroke distance.
? The inching distance in the inching mode remains the same.


Ver: 2019-06-06 (93)




1: Fix bugs in password modification for super administrators



Ver: 2019-06-18 (93)

1: Increase 239-245 output port number configuration parameters by default;
2: Add 461-468 input port number configuration parameters by default;
3: When the parameter interface is exited, the parameter number memory function is added, and the parameter interface is automatically positioned next time;
4: After the start processing is started, the focus is automatically switched to the "feedrate override", and the focus is automatically invalid after exiting the machining;
5: The switching focus is automatically disabled after the reset button is added;
6: Resolve the pause problem in the continuous movement of the A-axis after the setting soft limit is valid;
7: Solving the problem that the pulse distance is very short when the inching distance is short, causing manual movement;
8: Automatically limit the positive limit of the Z axis by increasing the total return to the workpiece zero mode;
9: Increase the information bar on the right side of the main interface.


Ver: 2019-06-19 (93)

1: Increase parameter 469 "Processing status display mode" percentage or remaining time
2: In the processing information bar on the right side of the main interface, increase the “remaining time” display;
3: Library file modification: all the return to workpiece zero process is changed to: when the current position of the Z axis is higher than the safe height, the last step Z axis

Do not perform the safe height action.


Ver: 2019-06-24 (93)

1: Pressing the “Spindle start/stop” button during processing is invalid.



Ver: 2019-07-23 (93)

1: Increase the metric system switching function, the parameter is 115
2: Adjust the coordinate display layout of the main interface


DM500 install 20190723.rar

1.2 MB, Down times: 91

Reply Support Opposition

Use props Report

5

Threads

56

Posts

316

Credits

Super Moderator

Rank: 8Rank: 8

Credits
316
QQ
 Author| Posted at 2019-8-12 21:30:03 | All floors
Ver: 2019-07-25 (93)

1: After the file is finished, if the A axis is under the rotation characteristic, the coordinates are automatically converted to 0-360.

Ver: 2019-08-01 (93)

1: Modify the semi-arc R programming overcut problem.


Ver: 2019-08-04 (93)
1: Increase the override adjustment delay, parameter 470: Feedrate override 1% change interval, in ns, default 20000ns
2: Correct the offset caused by the pulse equivalent calculation error when the A-axis is configured as the rotary axis.


DM500 install 20190804.rar

1.2 MB, Down times: 101

DM500 install 20190804

Reply Support Opposition

Use props Report

5

Threads

56

Posts

316

Credits

Super Moderator

Rank: 8Rank: 8

Credits
316
QQ
 Author| Posted at 2019-10-12 22:19:11 | All floors
Ver: 2019-10-12 (94)
1: The application software is compatible with the NAND memory version (memory size is 1G) and requires the latest hardware support;
2: In the file interface [Switch] button can be used to quickly switch U disk and local disk;
3: The file interface adds information such as the disk type and remaining space;
4: Parameter interface - advanced - parameter recovery adds two items, respectively, U disk recovery parameters and factory reset (default_setting);
5: File Interface - Advanced Add two operations: switch disk and fast copy operation;
6: The NAND memory version adds formatting operation. The specific operation is: long press the [spindle start/stop] button for 3 seconds;
7: Correct the XY-0 and ZA-0 button functions in the machine coordinate system;
8: Upgrade to version 94, modify the soft arc, the radius is too large, the program "fake death" problem;



DM500 install 20191012.rar

1.23 MB, Down times: 115

install 20191912

Reply Support Opposition

Use props Report

1

Threads

5

Posts

131

Credits

Registered member

Rank: 2

Credits
131
Posted at 2019-10-30 12:00:39 | All floors
Dear Enjoy-cnc,
I have 2 motion controller DM500 and Foinnc M130, they have the same parameters. Whether M130 can run DM500's rom. If not, do you know where to find its rom, I could not find it.
Thanks a lot!
Reply Support Opposition

Use props Report

5

Threads

56

Posts

316

Credits

Super Moderator

Rank: 8Rank: 8

Credits
316
QQ
 Author| Posted at 2019-10-30 21:45:59 | All floors
Dear dogovietvu
Hello there,
The M130 installation package is not the same as the DM500. You can try it with the M130 upgrade package below.
If the main interface after the upgrade shows Ver:2019-10-12(94)-chs, the upgrade is successful.
If Ver:2019-10-12(94)-XXX is displayed, you need to upgrade the DM500 installation package.

M130 install 20191012.rar

628.63 KB, Down times: 104

.M130 install 20191012

Reply Support Opposition

Use props Report

0

Threads

1

Posts

4

Credits

Newbie Member

Rank: 1

Credits
4
Posted at 2019-12-16 21:30:55 | All floors
How do you install and update your dm500
Reply Support Opposition

Use props Report

3

Threads

11

Posts

43

Credits

Newbie Member

Rank: 1

Credits
43
Posted at 2020-1-30 15:47:30 | All floors
Last edited by Kopf In 2020-1-30 15:49 Editor

Hello, the latest firmware (DM500 install 20191012.rar) has some issues. The same GCode which was running fine before now doesn't run properly. The work origin Z-axis resets to zero during the begin of the work. Needed to revert to the previous firmware (DM500 install 20190804.rar) to make it work again.

Here the GCode I was testing with:
  1. %
  2. (T1 D=2. CR=0. TAPER=118DEG - ZMIN=0. - SPOT DRILL)
  3. N10 G90 G94 G17 G49 G40 G80
  4. N15 G21
  5. N20 G28 G91 Z0.
  6. N25 G90

  7. (ENGRAVE1 -SQ)
  8. N30 T1 M06
  9. N35 S5000 M03
  10. N40 G54
  11. N45 M08
  12. N50 G00 X50. Y0.
  13. N55 G43 Z15. H01
  14. N60 G00 Z5.
  15. N65 G01 Z0. F1000.
  16. N70 Y50.
  17. N75 X0.
  18. N80 Y0.
  19. N85 X50.
  20. N90 G00 Z15.

  21. (ENGRAVE1 - CI)
  22. N95 G00 X25. Y50.
  23. N100 Z15.
  24. N105 Z5.
  25. N110 G01 Z0. F1000.
  26. N115 G03 Y0. J-25.
  27. N120 Y50. J25.
  28. N125 G00 Z15.

  29. N130 M09
  30. N135 G28 G91 Z0.
  31. N140 G90
  32. N145 G49
  33. N150 G28 G91 X0. Y0.
  34. N155 G90
  35. N160 M30
  36. %
Copy the code
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list