|
|
Last edited by enjoy_cnc In 2019-7-23 19:18 Editor
Ver: 2018-04-12-93H0918
1: Occasionally pop-up problem in the edit box in the dialog box
2:chs and eng 116-119 configuration error problem
Ver: 2018-04-12-93H1011
1: Feedrate override is effective for both G01 and G00
Ver: 2018-04-12-93H1026
1: Increase 238 parameters IO filter time unit is ms, that is, IO scan time [Supported by FPGA version 01 or higher]
2: Add the hardware ID number and FPGA version information in the lower right corner of the main interface, for example ID: 9d8322b6f5106490_01 indicates that the hardware ID is: 9d8322b6f5106490 FPGA version is 01
Ver: 2018-04-12-93H1117
1: Soft limit will not overshoot
Ver: 2018-04-12-93H1120
1: Increase parameter No. 105, A-axis rotation characteristic. If set to rotary axis, the A-axis is completed within one circle of the workpiece and the excess mechanical coordinates are cleared.
Ver: 2018-04-12-93H1122
1: After turning on the A-axis rotation characteristic, the specified line machining and the near-point machining A-axis can be positioned in one turn;
Ver: 2018-12-02 (93)
1: The output port is configurable;
Ver: 2018-12-12 (93)
1: Modify the tool setting method: Firstly obtain the mechanical position of each knife in the knife, and then clear it;
2: Increase tool library support;
3: Increase the operation in the middle
Ver: 2018-12-19 (93)
1: Modify the multi-axis manual at the same time and simultaneously release the occasional movement of an axis.
Ver: 2019-01-05 (93)
1: Increase the jog distance setting dialog box;
2: Increase the program to start the spindle automatic start setting, and automatically close the spindle setting when the program ends;
3: Increase the boot-back mechanical zero prompt;
4: Check whether to return to zero before running the program;
5: The parameters are divided into user parameters and vendor parameters (admin password entry) can be classified according to the manufacturer;
6: Increase the automatic processing of the specified line processing;
7: The spindle speed can be adjusted during machining;
8: Increase the floating tool setting and fixed tool setting. The floating tool setting should be set to the thickness (positive value). The fixed tool setting tool thickness is automatically set.
9: The switch button can be configured according to the user's cycle options;
Ver: 2019-01-07 (93)
1: The visitor can unlock the password;
Ver: 2019-01-08 (93)
1: Remove the manual magnification display, and the manual override is combined with the feedrate override;
2: Modify the time calculation error after the installment is unlocked;
Ver: 2019-01-16 (93)
1: Support V1.2 version registration machine
Ver: 2019-02-21 (93)
1: increase the common offset of each axis
2: Modify the coordinate conversion method of the tool, the thickness of the tool is positive: the tool is higher than the machined surface
Ver: 2019-03-04 (93)
1: Fixed the problem of returning only Z when all the workpieces were zero.
Ver: 2019-03-12 (93)
1: prompt to return to mechanical zero after power-on reset
Ver: 2019-03-13 (93)
1: Corrected the abnormality of processing half an hour after the upgrade [2019-03-10] version;
Ver: 2019-03-23 ??(93)
1: Add the manual upgrade function, enter the parameter interface-advanced-system upgrade-restart, and copy the install folder to the root directory of the U disk before upgrading. Note that there is no more folder under the install folder.
Ver: 2019-04-05 (93)
1: Increase the tool setting parameter 150, fixed tool setting safety height (mechanical coordinate), fixed tool setting action flow: Z rises to the 150th parameter mechanical position, then moves XY to the 72, 73 mechanical position, then Z moves to 74 Mechanical position
2: Increase the search speed of the No. 151 tool setting signal;
3: Spindle multi-speed is compatible with Weihong pirate card mode (3+0);
Ver: 2019-04-23 (93)
1: Automatic parameter increase No. 152 Parameter: Near point comparison error Value range: 0.5-100mm, used to set the comparison error in the near-point machining during advanced machining.
The smaller the setting, the more accurate the positioning (applicable to the relief file). If the processing is a long line segment, the smaller the setting may not be searched. It is recommended to set this parameter to be large.
Not suitable for multi-layer machining, comparison principle: only compare whether the XY position is at the nearest point.
Ver: 2019-05-07 (93)
1: Modify the inching dialog box, the common offset dialog box, and the parameter dialog box entry mode to increase the previous data display.
Ver: 2019-05-30 (93)
1: Increase the 174 and 180 parameters. The buttons in continuous manual mode can be set separately by short-stroke distance.
? The inching distance in the inching mode remains the same.
Ver: 2019-06-06 (93)
1: Fix bugs in password modification for super administrators
Ver: 2019-06-18 (93)
1: Increase 239-245 output port number configuration parameters by default;
2: Add 461-468 input port number configuration parameters by default;
3: When the parameter interface is exited, the parameter number memory function is added, and the parameter interface is automatically positioned next time;
4: After the start processing is started, the focus is automatically switched to the "feedrate override", and the focus is automatically invalid after exiting the machining;
5: The switching focus is automatically disabled after the reset button is added;
6: Resolve the pause problem in the continuous movement of the A-axis after the setting soft limit is valid;
7: Solving the problem that the pulse distance is very short when the inching distance is short, causing manual movement;
8: Automatically limit the positive limit of the Z axis by increasing the total return to the workpiece zero mode;
9: Increase the information bar on the right side of the main interface.
Ver: 2019-06-19 (93)
1: Increase parameter 469 "Processing status display mode" percentage or remaining time
2: In the processing information bar on the right side of the main interface, increase the “remaining time” display;
3: Library file modification: all the return to workpiece zero process is changed to: when the current position of the Z axis is higher than the safe height, the last step Z axis
Do not perform the safe height action.
Ver: 2019-06-24 (93)
1: Pressing the “Spindle start/stop” button during processing is invalid.
Ver: 2019-07-23 (93)
1: Increase the metric system switching function, the parameter is 115
2: Adjust the coordinate display layout of the main interface
|
|
Author