M150_DM500 Upgrade file download!!!

enjoy_cnc · Posted at 2020-2-1 20:54:15

Hello there

N20 G28 G91 Z0. ///
The action flow to execute this line is:
1: Z axis: move relative position Z0,
2 :: XYZ moves to the position of MACH coordinate X0 Y0 Z0 respectively
If you don't want to go back to MACH Z0, you can delete this line.

%
(T1 D=2. CR=0. TAPER=118DEG - ZMIN=0. - SPOT DRILL)
N10 G90 G94 G17 G49 G40 G80
N15 G21
N20 G28 G91 Z0. ///
N25 G90

(ENGRAVE1 -SQ)
N30 T1 M06
N35 S5000 M03
N40 G54
N45 M08
N50 G00 X50. Y0.
N55 G43 Z15. H01
N60 G00 Z5.
N65 G01 Z0. F1000.
N70 Y50.

Kopf · Posted at 2020-2-1 20:08:07

Hello,

Thanks for answering so quick. Please find attached the parameters file I exported from the controller.

enjoy_cnc · Posted at 2020-1-31 20:37:09

Last edited by enjoy_cnc In 2020-1-31 20:38 Editor

Ver: 2019-11-02 (94)
1: Modify the library file back to the workpiece zero process, 1: Increase the safety height higher than the current value, and finally return to the safe height 2: Consider the Z positive soft limit position when the Z axis is lower than the safe height;
2: The tool magazine capacity parameter is open. If the T code is ignored, the tool magazine capacity of No. 90 can be set to 0.

Ver: 2019-11-19 (94)
1: Modify the problem that the X07 tool setting function is not executed

Ver: 2019-11-27 (94)
1: Adjust the magnification adjustment action. The magnification adjustment between% 0-10% will decrease by 1%. If it is greater than 10%, each time you press the key, it will decrease by 10%.

Ver: 2019-11-28 (94)
1: Add parameter 153, specify the line scanning method, fast positioning can shorten the scanning time

Ver: 2019-12-03 (94)
1: Add processing file .FNC format, internal system encryption and decryption function. Document requirements <8M

Ver: 2019-12-05 (94)
1: Added manual encryption operation on the handle interface to solve the problem of failure to decrypt the time-locked fkey file due to failure to recognize the boot U disk;
Proceed as follows:
Copy fkey to the root directory of the USB flash drive-insert the USB flash drive-enter the parameter interface-advanced-software registration-manual decryption and encryption

Ver: 2019-12-25 (94)
1: the manual tool change function is lifted;
2: Tool magazine support;

Ver: 2020-01-07 (94)
1: Add parameter 471, A axis protection speed during processing
2: Coordinate system parameters are added for double backup, which can be saved in separate files.

enjoy_cnc · Posted at 2020-1-31 20:06:24

Hello there
Can you send me the parameter file setting, I will check your parameters.
Parameter file export method:
Parameter page ----- Advanced ------ Parameter backup to U disk

Thank you!

Kopf · Posted at 2020-1-30 15:47:30

Last edited by Kopf In 2020-1-30 15:49 Editor

Hello, the latest firmware (DM500 install 20191012.rar) has some issues. The same GCode which was running fine before now doesn't run properly. The work origin Z-axis resets to zero during the begin of the work. Needed to revert to the previous firmware (DM500 install 20190804.rar) to make it work again.

Here the GCode I was testing with:

%
(T1 D=2. CR=0. TAPER=118DEG - ZMIN=0. - SPOT DRILL)
N10 G90 G94 G17 G49 G40 G80
N15 G21
N20 G28 G91 Z0.
N25 G90
(ENGRAVE1 -SQ)
N30 T1 M06
N35 S5000 M03
N40 G54
N45 M08
N50 G00 X50. Y0.
N55 G43 Z15. H01
N60 G00 Z5.
N65 G01 Z0. F1000.
N70 Y50.
N75 X0.
N80 Y0.
N85 X50.
N90 G00 Z15.
(ENGRAVE1 - CI)
N95 G00 X25. Y50.
N100 Z15.
N105 Z5.
N110 G01 Z0. F1000.
N115 G03 Y0. J-25.
N120 Y50. J25.
N125 G00 Z15.
N130 M09
N135 G28 G91 Z0.
N140 G90
N145 G49
N150 G28 G91 X0. Y0.
N155 G90
N160 M30
%

Copy the code

enjoy_cnc · Posted at 2019-12-28 22:27:47

1. Copy the upgrade folder install to the root directory of the USB flash drive;
2. Insert U disk and power off and restart;
3. The system will automatically search for the upgrade file to upgrade. During the upgrade, the interface will stay at the boot interface for about 10 S. Please wait patiently and do not power off;
4. Check if the version date of the main control interface is the same as that provided by the customer after booting;

Garethg · Posted at 2019-12-16 21:30:55

How do you install and update your dm500

enjoy_cnc · Posted at 2019-10-30 21:45:59

Dear dogovietvu，
Hello there,
The M130 installation package is not the same as the DM500. You can try it with the M130 upgrade package below.
If the main interface after the upgrade shows Ver:2019-10-12(94)-chs, the upgrade is successful.
If Ver:2019-10-12(94)-XXX is displayed, you need to upgrade the DM500 installation package.

dogovietvu · Posted at 2019-10-30 12:00:39

Dear Enjoy-cnc,
I have 2 motion controller DM500 and Foinnc M130, they have the same parameters. Whether M130 can run DM500's rom. If not, do you know where to find its rom, I could not find it.
Thanks a lot!

enjoy_cnc · Posted at 2019-10-12 22:19:11

Ver: 2019-10-12 (94)
1: The application software is compatible with the NAND memory version (memory size is 1G) and requires the latest hardware support;
2: In the file interface [Switch] button can be used to quickly switch U disk and local disk;
3: The file interface adds information such as the disk type and remaining space;
4: Parameter interface - advanced - parameter recovery adds two items, respectively, U disk recovery parameters and factory reset (default_setting);
5: File Interface - Advanced Add two operations: switch disk and fast copy operation;
6: The NAND memory version adds formatting operation. The specific operation is: long press the [spindle start/stop] button for 3 seconds;
7: Correct the XY-0 and ZA-0 button functions in the machine coordinate system;
8: Upgrade to version 94, modify the soft arc, the radius is too large, the program "fake death" problem;

M150_DM500 Upgrade file download!!!

View forum before

TEL

0755-87654321