Still trying to upload

Will_D

Anything come through?

Nikolay81

Will_D Posted at 2018-9-10 23:54
The user sets the initial Y position before starting the probe so its only X that needs #2010.

По ...

Thank you. I understood what your idea is. But it seems to me that it is much more convenient to immediately set the tool, with the X and Y axes offset and not only the Y axis.
Since, the tool will be too close to the edge of the sensor and it is likely that when Z is lowered, it may miss the sensor.
Perhaps, it will be convenient for someone.
I think you should make a video about the usefulness of the parameter # 2010.

DWeaver

This is an old post that I have been reading through to find answers about the probing functionality, but still unsure of some of the settings.

I want to set my probe up in the controller.  I purchased a corner probe that is triangular, and I have been working on the setting to get the probe function to work on the controller...

#68 - 3 - Puts the  controller into probing mode #3
#2000 - ? - diameter of probe
#2001: 8.06mm - Tool plate  thick for X
#2002: 7.77mm - Tool plate  thick for Y
#2003: 3.6mm - Tool plate  thick for Z
#2004: -20mm - shift of X  axis before probed
#2005:  50mm - shift of Y  axis before probed
#2006:  5mm - Z position  before X(Y)-axis probed
#2007:  5mm  - Back distance when tool touches X-axis
#2008:  5mm - Back distance when tool touches Y-axis
#2009:  5mm  -Back distance when tool touches Z-axis
#2010:  ?  -  center of  tool plate
#2011:  ?  Probe feedrate

I am not sure if the ones I have filled in are right, and I cannot figure out the ones with the question mark.
#2000 - shouldn't this depend on what size endmill I am using?
#2010 - This just makes zero sense at all to me, not sure why the center of the probe plate is important.
#2011 - it indicates that this is in relation to "G01 command in relative (G91) mode" - not sure what that means.. I think that 3mm/sec should be fast enough to start, and I can speed up or slow down from there.

Will_D

The user sets the initial Y position before starting the probe so its only X that needs #2010.

Пользователь устанавливает начальную позицию Y перед запуском зонда, поэтому его единственный X, который нуждается в # 2010.

alexwalex

Первичное смещение по x задается #2004, после нахождения 0 по X щуп выходит ро  X в координату #2010, затем отходит по Y на #2005 и замеряет Y.

Nikolay81

alexwalex Posted at 2018-9-10 20:32
#2010 - величина смещения щупа по X относительно уже измер ...

Я это знаю. Почему только по X? Логичнее было бы сделать и по Y то же. Или я что-то не понимаю?

alexwalex

#2010 - величина смещения щупа по X относительно уже измеренного X0 заготовки перед выполнением пробинга по Y.

Nikolay81

alexwalex Posted at 2018-9-10 19:28
Сейчас помочь особо не могу т.к. нахожусь в командировк ...

I do not understand why the # 2010 "center of tool plate" parameter is needed?
It seems that he must mix the instrument to the center of the sensor if the edges of the sensor are poorly treated / damaged / contain screw.
But then, a similar parameter is needed for the Y axis. Why only on X?
It is necessary that he determines the edge of X, then he defines the edge along Y (with offset # 2010), and then again on X (with offset # 2010).
What do you think? In my opinion, it turns out illogically.

alexwalex

Сейчас помочь особо не могу т.к. нахожусь в командировке. Вот тут пытался объяснить значения параметров:
http://www.cnc-club.ru/forum/vie ... p;start=240#p454240

Nikolay81

alexwalex Posted at 2018-9-10 01:15
It was me. You have any question?

Можете ли Вы написать инструкцию для пробинга на Русском? Многим русскоязычным пользователям DDCSV, это бы очень помогло.
Также, я хочу узнать Ваше мнение о переводе настроек пробинга. Возможно, по Вашему мнению, некоторые пункты, надо перевести по-другому? (см. файл rus в архиве).