Firmware download

ytliu

Ver:2018-07-05-95 Modification:
1. Increase keyboard support
2. Increase the trial cut (handwheel guide) function
3. Add file editing function

Key mapping description:

X-: LEFT ARROW(←)、Numeric keypad '4'
X+: RIGHT ARROW(→)、Numeric keypad '6'
Y-: DOWN ARROW(↓)、Numeric keypad '2'
Y+: UP ARROW(↑)、Numeric keypad '8'
Z-: PAGEDOWN、Numeric keypad '3'
Z+: PAGEUP、Numeric keypad '9'
A-: Numeric keypad '1'
A+: Numeric keypad '7'


the centering operation:F3(Used in conjunction with the MPG axis selection. Only when the MPG axis is selected as X or Y, the corresponding axis performs the centering operation.)
Goto Zero:F5、Numeric keypad '0'(Used in conjunction with the MPG axis selection. If the MPG axis is selected to be empty, the whole axis will be goto zero. If the MPG axis is selected as X, the X axis will be goto zero.)
Zero:F6、Numeric keypad 'DEL'(Used in conjunction with the MPG axis selection.If the MPG axis is selected to be empty, the whole axis will be zero. If the MPG axis is selected as X, the X axis will be zero.)
Home:F7(The first press enters the HOME mode. In the HOME mode, press again to perform full axis HOME, or press the corresponding axis selection key, the corresponding axis will perform HOME separately.)
HOME X-axis selection:'X'
HOME Y-axis selection:'Y'
HOME Z-axis selection:'Z'
HOME A-axis selection:'A'
PROBE:F8(The first press enters PROBE mode and presses again to perform the PROBE operation.)

Manual mode switching:F10、Numeric keypad '*'
Jog distance adjustment:Numeric keypad '5'
FRO adjustment:'F'、'8'
SRO adjustment:'S'、'9'
Coordinate system selection:'G'、'0'


START:SCROLL LOCK、Numeric keypad '-'
PAUSE: PAUSE BREAK、Numeric keypad '+'
TRCUT:F11、Numeric keypad 'ENTER'
Single-stage processing mode:F4(The single-segment mode can be switched while the system is idle. After starting the machining in single-segment mode, the system executes one line each time the start button is pressed.)

Focus TAB：F9、Numeric keypad '/'
Focus adjustment+:'+'
Focus adjustment-:'-'

Page switching:TAB、BACKSPACE
Track display：F12

Uninstall U disk: DELETE

Xyem_no_ctoly

Здравствуйте,если я хочу оставить свою прошивку на контроллере но нужно мне изменить язык интерфейса как мне поступить где и какой файл куда вставлять,заранее спасибо

Wlod

Hello everyone!!
writes by google translator
because I am from Poland.
I have DDCSV1.1 with an update
2018-10-09-101
a serious problem with reading the hole code, e.g.
of these holes made, the contour is made normally and the other enters with a milling cutter without a contour at full depth.
I generate paths from mastercam x3. Regards and please help

ytliu

Hi Stein,
First of all, I want to know if you have successfully upgraded. For example, if you upgrade using install(2019-06-10-111).zip, after the upgrade is successful, Ver:2010-06-10-111NOR will be displayed in the lower right corner of the screen.

ytliu

Thank you, I will modify it.

ytliu

You can modify the configuration file.

If your language is English, open eng with Notepad and find this line.
#224 -t1 -s1"Spindle M3/M4/M5 response Duration" -s2"s" -m6 -min=0.000 -max=9.000
Change 9.000 to 20.000, then reinstall eng into the controller

ytliu

Ver:2018-10-09-101 Description:
1. On the file and parameter page, you can operate through the handwheel;
2. Increase #2031 uniaxial acc is limited by M_Ctrl start acc;
3. Increase #2030 Soft-limited stop mode;
4. Increase #2029 color reversal;

ytliu

r6mf49t2 Posted at 2018-10-9 14:12
Спасибо за ваш труд) Возможно ли обновить только файл  ...

yes

r6mf49t2

Nikolay81 Posted at 2018-9-26 20:29
I edited the Russian translation. In all the following firmwares, you should use this file.

Спасибо за ваш труд) Возможно ли обновить только файл перевода без обновления прошивки? Для этого в папку install  нужно поместить только файл rus?

ytliu

maxx2000 Posted at 2018-10-2 21:50
firmware 2018-09-07-100
The problem with the hang has remained.
1. Run the program.

Your analysis is correct, there are some conflicts in MPG mode.

In MPG mode, if the system is in FRO state, press the start button at this time, FRO will be set to 0, which will cause the maching to be in a pause state (you said the frozen state), at this time you can adjust the FRO by handwheel Value to resume maching.

ytliu

maxx2000 Posted at 2018-9-21 22:56
With the latest firmware(2018-09-07-100).zip), the following happens.
Start  program, and hit the FR ...

I found the reason for this error, because #2028 is a new parameter, after the installation is complete, #2028=0, you need to reset this parameter, such as 10.