Different speed with the same code - DDCSV2.1 - Standalone CNC Motion Controller - Digital Dream Technology support
12Next
Return to List Add thread
View: 11474|Reply: 11
Print Previous Topic Next Topic

Different speed with the same code

[Copy Link]

3

Threads

24

Posts

184

Credits

Registered member

Rank: 2

Credits
184
Jump to the specified floor
Landlord
Posted at 2019-3-23 03:48:40 | Only Author Replies reward |Descending browser |Read mode
First I want to thank for the help. I changed the software version from 89 to 106. At the new version there is a difference in the logic of PWM and M3 and a bit difficult to understand the logic, but I get it right. Probe is already working and this video shows the result of it . There is, however, a strange problem. The controller changes the speed of two separate files in which a part of the code is the same. This is the code with which I cut, I just copied the same code and the speed is visibly different.
What can be attributed to this?

Reply

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
Sofa
Posted at 2019-3-23 06:30:48 | Only Author
Congratulations on solving the probe problem.
Can you describe this speed difference problem in more detail? It is best to provide the relevant g code and configuration.
Reply Support Opposition

Use props Report

3

Threads

24

Posts

184

Credits

Registered member

Rank: 2

Credits
184
Bench
 Author| Posted at 2019-3-23 15:43:27 | Only Author
Well the problem is visible in the video that I have given. First, the machine cuts the profile and this is a separate file because it may have to be done at the beginning of each profile. Then I run a second file that makes two opposite holes and the same cut off. For the second cut, I just copied the code from the first file. The speed is visibly different.
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
Floor
Posted at 2019-3-23 20:49:26 | Only Author
I can't make accurate judgments about the information you provide. You can check the following items:
1. The speed of G0 is determined by the #80 parameter, not the F programming word;
2. The #125 parameter can affect the speed of G2/G3, such as F=1000mm/min, #125=0.5, then the speed of G2/G3 is F*#125=500mm/min;
Reply Support Opposition

Use props Report

3

Threads

24

Posts

184

Credits

Registered member

Rank: 2

Credits
184
5#
 Author| Posted at 2019-3-23 23:16:47 | Only Author
The Y,Z and A movement of the cut is only with G1.
Reply Support Opposition

Use props Report

3

Threads

24

Posts

184

Credits

Registered member

Rank: 2

Credits
184
6#
 Author| Posted at 2019-3-25 23:26:05 | Only Author
Last edited by stivemaster In 2019-3-26 00:02 Editor

This forum obviously does not answer all questions.However, I will try again and upload the problem files.
When running file 21, the speed of movement on Y, Z and A is greater than when the file 22 is released. I wonder why this happens?
Additionally, the problem is not only with the speed set by the F and G00 speed and it performs many times at high speed.

1.zip

3.24 KB, Down times: 1086

Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
7#
Posted at 2019-3-26 06:52:58 | Only Author
How is your #6 parameter set? If the #6 parameter is not equal to 3, the system will automatically optimize the speed, you can configure it to 3, turn off the speed optimization function.
Reply Support Opposition

Use props Report

3

Threads

24

Posts

184

Credits

Registered member

Rank: 2

Credits
184
8#
 Author| Posted at 2019-3-27 00:15:25 | Only Author
Last edited by stivemaster In 2019-3-27 00:34 Editor

What does this parameter mean and where does the manually talk about it?
And I could not understand why G02 and G03 are running at half speed ?

Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
9#
Posted at 2019-3-27 09:46:21 | Only Author
Reply Support Opposition

Use props Report

3

Threads

24

Posts

184

Credits

Registered member

Rank: 2

Credits
184
10#
 Author| Posted at 2019-3-27 17:09:46 | Only Author
Do you mean that axis that is rotating should I set it as linear?
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list