Still trying to upload - On 2 Page - DDCSV2.1 - Standalone CNC Motion Controller - Digital Dream Technology support
12
Return to List Add thread
Author: Will_D

Still trying to upload

[Copy Link]

0

Threads

26

Posts

1667

Credits

Gold member

Rank: 6Rank: 6

Credits
1667
Posted at 2018-9-10 23:53:54 | All floors
Первичное смещение по x задается #2004, после нахождения 0 по X щуп выходит ро  X в координату #2010, затем отходит по Y на #2005 и замеряет Y.
Reply Support Opposition

Use props Report

9

Threads

53

Posts

669

Credits

Senior Member

Rank: 4

Credits
669
 Author| Posted at 2018-9-10 23:54:16 | All floors
The user sets the initial Y position before starting the probe so its only X that needs #2010.

Пользователь устанавливает начальную позицию Y перед запуском зонда, поэтому его единственный X, который нуждается в # 2010.
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-11 01:28:05 | All floors
Will_D Posted at 2018-9-10 23:54
The user sets the initial Y position before starting the probe so its only X that needs #2010.

По ...

Thank you. I understood what your idea is. But it seems to me that it is much more convenient to immediately set the tool, with the X and Y axes offset and not only the Y axis.
Since, the tool will be too close to the edge of the sensor and it is likely that when Z is lowered, it may miss the sensor.
Perhaps, it will be convenient for someone.
I think you should make a video about the usefulness of the parameter # 2010.
Reply Support 0 Opposition 1

Use props Report

1

Threads

2

Posts

9

Credits

Newbie Member

Rank: 1

Credits
9
Posted at 2021-1-13 09:17:14 | All floors
This is an old post that I have been reading through to find answers about the probing functionality, but still unsure of some of the settings.

I want to set my probe up in the controller.  I purchased a corner probe that is triangular, and I have been working on the setting to get the probe function to work on the controller...

#68 - 3 - Puts the  controller into probing mode #3
#2000 - ? - diameter of probe
#2001: 8.06mm - Tool plate  thick for X
#2002: 7.77mm - Tool plate  thick for Y
#2003: 3.6mm - Tool plate  thick for Z
#2004: -20mm - shift of X  axis before probed
#2005:  50mm - shift of Y  axis before probed
#2006:  5mm - Z position  before X(Y)-axis probed
#2007:  5mm  - Back distance when tool touches X-axis
#2008:  5mm - Back distance when tool touches Y-axis
#2009:  5mm  -Back distance when tool touches Z-axis
#2010:  ?  -  center of  tool plate
#2011:  ?  Probe feedrate

I am not sure if the ones I have filled in are right, and I cannot figure out the ones with the question mark.
#2000 - shouldn't this depend on what size endmill I am using?
#2010 - This just makes zero sense at all to me, not sure why the center of the probe plate is important.
#2011 - it indicates that this is in relation to "G01 command in relative (G91) mode" - not sure what that means.. I think that 3mm/sec should be fast enough to start, and I can speed up or slow down from there.
CornerProbe.jpg
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list