Still trying to upload - DDCSV2.1 - Standalone CNC Motion Controller - Digital Dream Technology support
12Next
Return to List Add thread
View: 3939|Reply: 13

Still trying to upload

[Copy Link]

9

Threads

53

Posts

669

Credits

Senior Member

Rank: 4

Credits
669
Posted at 2018-9-8 23:38:27 | All floors |Read mode
Anything come through?

DDCSV Probing Modes.pdf

157.06 KB, Down times: 220

Reply

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-11 01:28:05 | All floors
Will_D Posted at 2018-9-10 23:54
The user sets the initial Y position before starting the probe so its only X that needs #2010.

По ...

Thank you. I understood what your idea is. But it seems to me that it is much more convenient to immediately set the tool, with the X and Y axes offset and not only the Y axis.
Since, the tool will be too close to the edge of the sensor and it is likely that when Z is lowered, it may miss the sensor.
Perhaps, it will be convenient for someone.
I think you should make a video about the usefulness of the parameter # 2010.
Reply Support 0 Opposition 1

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-9 17:11:51 | All floors
Thank you very much for the instruction. Do you speak Russian?
Reply Support Opposition

Use props Report

9

Threads

53

Posts

669

Credits

Senior Member

Rank: 4

Credits
669
 Author| Posted at 2018-9-9 19:47:33 | All floors
Nikolay81 Posted at 2018-9-9 17:11
Thank you very much for the instruction. Do you speak Russian?

Sorry I don't speak Russian!
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-10 01:06:37 | All floors
Will_D Posted at 2018-9-9 19:47
Sorry I don't speak Russian!

The fact that the video, which depicts the work mode3, on YouTube posted a man named Alexey Konev. I thought it was you.
Reply Support Opposition

Use props Report

0

Threads

26

Posts

1665

Credits

Gold member

Rank: 6Rank: 6

Credits
1665
Posted at 2018-9-10 01:15:11 | All floors
It was me. You have any question?
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-10 18:02:51 | All floors
alexwalex Posted at 2018-9-10 01:15
It was me. You have any question?

Можете ли Вы написать инструкцию для пробинга на Русском? Многим русскоязычным пользователям DDCSV, это бы очень помогло.
Также, я хочу узнать Ваше мнение о переводе настроек пробинга. Возможно, по Вашему мнению, некоторые пункты, надо перевести по-другому? (см. файл rus в архиве).

rus.rar

4.79 KB, Down times: 78

Reply Support Opposition

Use props Report

0

Threads

26

Posts

1665

Credits

Gold member

Rank: 6Rank: 6

Credits
1665
Posted at 2018-9-10 19:28:10 | All floors
Сейчас помочь особо не могу т.к. нахожусь в командировке. Вот тут пытался объяснить значения параметров:
http://www.cnc-club.ru/forum/vie ... p;start=240#p454240
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-10 20:11:02 | All floors
alexwalex Posted at 2018-9-10 19:28
Сейчас помочь особо не могу т.к. нахожусь в командировк ...

I do not understand why the # 2010 "center of tool plate" parameter is needed?
It seems that he must mix the instrument to the center of the sensor if the edges of the sensor are poorly treated / damaged / contain screw.
But then, a similar parameter is needed for the Y axis. Why only on X?
It is necessary that he determines the edge of X, then he defines the edge along Y (with offset # 2010), and then again on X (with offset # 2010).
What do you think? In my opinion, it turns out illogically.
Reply Support Opposition

Use props Report

0

Threads

26

Posts

1665

Credits

Gold member

Rank: 6Rank: 6

Credits
1665
Posted at 2018-9-10 20:32:04 | All floors
Last edited by alexwalex In 2018-9-10 20:33 Editor

#2010 - величина смещения щупа по X относительно уже измеренного X0 заготовки перед выполнением пробинга по Y.
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-10 22:58:58 | All floors
alexwalex Posted at 2018-9-10 20:32
#2010 - величина смещения щупа по X относительно уже измер ...

Я это знаю. Почему только по X? Логичнее было бы сделать и по Y то же. Или я что-то не понимаю?
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list