Работа выносного пульта - DDCSV3.1 Standalone CNC Motion Controller - Digital Dream Technology support
View: 351|Reply: 8

Работа выносного пульта

[Copy Link]

1

Threads

1

Posts

5

Credits

Newbie Member

Rank: 1

Credits
5
Posted at 2020-11-4 13:50:21 | All floors |Read mode
Добрый день! Приобрел контроллер DDCS V3.1, сделал первичные настройки. С самого контроллера оси двигаются, никаких вопросов нет, а вот с пульта какой то косяк: независимо от того какая ось переключателем выбрана едет только ось X (даже если выбран Off), множитель также не играет никакой роли - всегда едет на один шаг шагового двигателя. На видео все видно https://youtu.be/y19QWT0qaxc
Reply

Use props Report

0

Threads

2

Posts

6

Credits

Newbie Member

Rank: 1

Credits
6
Posted at 2020-12-10 19:29:19 | All floors
1 /Обязательно подключить контроллер +24 и GND  и СOM+  и COM-  тоже подать питание (можно и с того-же   источника 24)
2. Проверить распайку  пульта . Вот сайт на ютюбе, брал с него пример (msdesign.ru)
3/ Проверить работу энкодера можно так = войти в меню настройки (Top paramets)дважды нажав на клавишу PAGE R  , покрутить колесо энкодера ,должен перемещаться по   меню .Если ок то переходи в настройки MPG/
4/выбрать настройки  MPG 428 включить 429 высокий 430 стандарт 431 -0.001 432 низкий 434 высокий 448 открытый 2028 -10 .2044 yes/
Reply Support 1 Opposition 0

Use props Report

2

Threads

4

Posts

22

Credits

Newbie Member

Rank: 1

Credits
22
Posted at 2020-11-4 19:26:36 | All floors
Bom dia! Eu comprei um controlador DDCS V3.1 V3 fiz as configurações dos eixos X Y Z Mais o quarto eixo "A" não consigo configurar as suas configuracão MOTOR DE PASSO NEME 23 1.8 ANGULO 15 KGF                                                                     
Reply Support Opposition

Use props Report

0

Threads

22

Posts

72

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
72
Posted at 2020-11-4 23:05:42 | All floors
Hello, you use the MPG to control, or use the controller keys?
Reply Support Opposition

Use props Report

0

Threads

22

Posts

72

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
72
Posted at 2020-11-4 23:08:21 | All floors
Ok, I checked with your video. The MPG wiring is wrong, I think XYZA of MPG, all wired to X of the controller. Check your MPG wiring!
Reply Support Opposition

Use props Report

0

Threads

22

Posts

72

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
72
Posted at 2020-11-4 23:08:27 | All floors
Ok, I checked with your video. The MPG wiring is wrong, I think XYZA of MPG, all wired to X of the controller. Check your MPG wiring!
Reply Support Opposition

Use props Report

0

Threads

22

Posts

72

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
72
Posted at 2020-11-4 23:08:33 | All floors
Ok, I checked with your video. The MPG wiring is wrong, I think XYZA of MPG, all wired to X of the controller. Check your MPG wiring!
Reply Support Opposition

Use props Report

0

Threads

2

Posts

6

Credits

Newbie Member

Rank: 1

Credits
6
Posted at 2020-12-10 19:36:59 | All floors
Прошивка 2020-03-06-112NOR . Пиши НА вотцап  8916 175 48 26 (Москва часовой пояс) или звони .Константин Тарасов.
Reply Support Opposition

Use props Report

1

Threads

4

Posts

19

Credits

Newbie Member

Rank: 1

Credits
19
Posted at 2021-1-13 14:39:58 | All floors
Have you connected two 24v power supplies to your controller?
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list