Firmware download

Kev0 · Posted at 2018-10-18 03:04:04

@ytliu Thank you very much!
@ Nikolay81 it's not about the braking time. The time to accelerate the spindle is to long. I got a NOWFOREVER E-100 but the settings how to set the ramp up time are not described anywhere. For the D-100 there is a manual but the settings regarding to the rampup are different (D-100 is 1-7 /E-100 defalut 400). So I have to compensate this via the DDCSV.

Btw. really great to have such a good support !!

Nikolay81 · Posted at 2018-10-18 05:37:44

Last edited by Nikolay81 In 2018-10-18 05:56 Editor

Kev0 Posted at 2018-10-18 03:04
@ytliu Thank you very much!
@ Nikolay81 it's not about the braking time. The time to accelerate the ...

This cannot be compensated through DDCSV.
Take a multimeter and see the rise time of the VSO voltage. If it is small, then the reason is in the inverter.Also, it is necessary to connect the VSO input with + 10V in the inverter and see the acceleration time.I attached the instructions to the message. Have you ever looked for it on the Internet?

Kev0 · Posted at 2018-10-18 14:20:35

Sorry said it the wrong way. I got a D-100 and there is no manual available.

Why this cant be compensated ? Sure it can.
I set the rampup in DDCSV to 0 wich results in a 0-10V in no time. (Spindle reacts the same way -> ramp slow)
As the spindle runs its ramping curve it just needs more time to reach the desired speed.
In order to have the right cutting speed set the DDCSV to wait a bit longer. Everything is working.

Would be nicer to change the spindle ramping map but this is not possible without a manual .

Nikolay81 · Posted at 2018-10-18 15:56:50

Kev0 Posted at 2018-10-18 14:20
Sorry said it the wrong way. I got a D-100 and there is no manual available.

Why this cant be compe ...

See this instruction. https://cloud.mail.ru/public/Fg71/dw2VRmveu They say that it fits. Judging by the information on the forums - this inverter is buggy. There are a lot of problems with it.

maxx2000 · Posted at 2018-10-30 13:52:27

Marked one bug.
In the inverse screen layout, if you press FRO, then choose M5. The entire screen is highlighted.

ytliu · Posted at 2018-10-30 15:28:40

Thank you, I will modify it.

dexpiste · Posted at 2019-5-11 07:10:45

Last edited by dexpiste In 2019-5-11 07:12 Editor

Edit:

Palavan · Posted at 2019-5-28 20:32:25

Tell me please. When you download a file, you can not see the processing path, is it just me or everyone?
I would like to differentiate amongst what we will do on the file name you can not remember.
I have a machine for cutting foam (facade decoration, 2D processing)
Or what to change in the settings to see it?

Stein · Posted at 2019-7-8 19:33:21

Good afternoon, I am writing to you in the hope of your help. I bought a DDCSV2.1 controller on 4 axes, for me it was important, until I bought a rotary axis on the settings, I didn’t look at all that. Everything works, but when I started to set everything up, I noticed that I have no axis A in the settings and all the settings regarding it. The most important thing on the back of the sticker and on the connector is that on the controller 4 axes. on the display, connected to the output axis And another axis to find out if it works or not — works. Tell me what to do, they said you need to install another firmware, I tried the other firmware does not stand up, nothing changes. USB flash drive la together with the controller. I don’t understand anything, I tried everything. Yes, and even in the settings there is such a very first Top Parametrs item, so there’s nothing empty under it. Just a line with this phrase. I hope for your help. Thank you very much.

ytliu · Posted at 2019-7-8 22:49:30

Hi Stein,
First of all, I want to know if you have successfully upgraded. For example, if you upgrade using install(2019-06-10-111).zip, after the upgrade is successful, Ver:2010-06-10-111NOR will be displayed in the lower right corner of the screen.

Firmware download

TEL

0755-87654321