Firmware download

Nikolay81 · Posted at 2018-7-19 23:09:25

Thank you very much for improving the software, this wonderful controller.
Sorry for the bad english - I write through Google translator.
There is a problem with the usb keyboard. If, hold and hold the button for
moving any axis for a long time, after releasing the button, the axis continues to move.
It can be fixed?

Nikolay81 · Posted at 2018-7-20 17:15:19

ytliu Posted at 2018-7-20 08:26
sorry! I did not find the problem you described, try another usb keyboard

The problem occurs when the keyboard is connected directly, without a USB hub. But with the hub, the response speed for releasing the key is greater than on the controller itself. That is, with manual control from the USB keyboard, the axis does not stop very fast. Can I reduce the response time for releasing the keys?

Nikolay81 · Posted at 2018-7-27 17:34:11

alexwalex Posted at 2018-7-27 16:14
ytliu, fix please in firmware files "eng" and "rus" parameter #55 translation string "Enable Z Home ...

Yes. There is such a problem. But I corrected manually.

Nikolay81 · Posted at 2018-7-31 20:48:27

ytliu Posted at 2018-7-31 06:21
Ver:2018-07-30-98 Description:
1. Add the user-defined system parameter area (#2000-#2499). After th ...

Dear Ytliu! Thank you very much!
Only now I noticed that the support of the Russian language has appeared.
I will make a quality translation into Russian, for 2-3 weeks.
A good translation takes a lot of time, and now a lot of work.
After I finish the translation, I will spread the information about this at the Russian CNC forums.
For sure, after this, DDCSV will buy a lot more in Russia.

Nikolay81 · Posted at 2018-8-1 00:33:48

ytliu Posted at 2018-7-27 10:44
Ver: 2018-07-27-97 Modification:
1. Increase Russian support,configure #1 (language setting) to 2 so ...

Translation was not an easy task.
Probably, my hair will turn gray before the time with this controller :-)
If I'm translate the "rus" file to line 54, the controller hangs if I open the parameters page and leave it for 10 minutes.
If I translate further lines 54 - the controller hangs, at an exit from page of parameters.
I attached a partial translation file.

There is one more problem - if you put the "rus" file ONLY in the INSTALL folder, sometimes the controller resets all the settings.

Can this be won?

I could do a preliminary translation, tomorrow, if the controller stops hanging.

Nikolay81 · Posted at 2018-8-1 19:47:06

Last edited by Nikolay81 In 2018-8-1 19:48 Editor

ytliu Posted at 2018-8-1 06:44
Thank you very much. I have fixed this problem.

I finished the preliminary translation.
Surely, there are a lot of mistakes in it :-)
Those settings that I have not translated - I do not understand.
On some of them, I asked you, but did not understand your explanation.
Later I'll ask again.
Some settings have been added new. I have not had time to deal with them yet.

In any case, this translation can already be used.
Add it to all subsequent firmware.
Later I will finalize the translation.

Aliexpress sells 1/3 of its customers in Russia.
In this case, please inform sellers of Aliexpress that they add to the product description, support of the Russian language.
This will increase sales.

There are some problems:
-Parameter # 16 - buggy. If you enter a value of 7, an empty string will be written. In English too.
-If translate READY (in Russian "ГОТОВ") on the screen will be written "ГОТ". That is, only the first 3 characters.
-The same with RESET.

Nikolay81 · Posted at 2018-8-2 20:22:54

ytliu Posted at 2018-8-2 16:14
Now increase the number of characters displayed on the main page. When you translate, consider the ...

Thank you.
Now all is well.
I attached the updated translation to the message.
Settings that I do not understand, I will translate later.
But there are not many of them.

Nikolay81 · Posted at 2018-8-3 03:00:37

Last edited by Nikolay81 In 2018-8-3 03:03 Editor

Corrected the Russian translation.
Now it has become even more convenient.

Nikolay81 · Posted at 2018-8-4 18:29:17

Last edited by Nikolay81 In 2018-8-4 18:32 Editor

There are many important changes:
-Cycle G83, now works correctly. Syntax: G83 X Y Z R Q I K. All parameters must be specified. Usually, K=1; I=0
-Added cycle G73. Syntax: G73 X Y Z R Q I K. All parameters must be specified. "I" is the distance of the retract. K=1
-The command M110 is added. This is an analog of M0, but the Z axis does not rise. Also, when using this command, a beep sounds.
-Added command G153. This is analog G53 (go to machine coordinates). Example G153 X0 Y0 F6000
-The command G92 is fixed. Example G90 G92 X0 Y0 (zero the X and Y axes).
-In lines with comments, now only comments are displayed. For example, to manually change an instrument, you write M110 (tool name).
Now only the contents of the brackets will be written on the screen. That is "tool name". This gives more space for the name of the instrument.
-Many small fixes.

An example of using new features can be found in the topic "Postprocessor for SheetCam"

Nikolay81 · Posted at 2018-8-8 15:26:26

maxx2000 Posted at 2018-8-8 14:16
Hey. And where you can see the full list of supported G and M codes

A complete list can always be seen in the file slib.nc
The list with a detailed description will be a little later.
You can help make it up.

Firmware download

TEL

0755-87654321