Firmware download - On 7 Page - DDCSV2.1 - Standalone CNC Motion Controller - Digital Dream Technology support
Author: ytliu

Firmware download

[Copy Link]

0

Threads

5

Posts

28

Credits

Newbie Member

Rank: 1

Credits
28
Posted at 2018-9-26 17:31:03 | All floors
Last edited by Kev0 In 2018-9-26 17:58 Editor

Hi,
I noticed some weird behaviour in r100. Sometimes the Software Endstop will be triggered but the beeping sound wont be reseted when moving out of it.
And the most annoying thing is that the probing wont work anymore. I straight came from something like r80 (cant remember the correct verion)
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-26 20:29:17 | All floors
I edited the Russian translation. In all the following firmwares, you should use this file.

rus.rar

4.81 KB, Down times: 160

Reply Support Opposition

Use props Report

0

Threads

22

Posts

370

Credits

Intermediate Member

Rank: 3Rank: 3

Credits
370
Posted at 2018-10-2 21:50:16 | All floors
Last edited by maxx2000 In 2018-10-2 21:52 Editor

firmware 2018-09-07-100
The problem with the hang has remained.
1. Run the program.
2. press FRO button
3.Rotate the handwheel to change the feed value.
if after that you press the pause button and then resume operation, the controller freezes. Only the Reset button works.
If the feed is adjusted with buttons, this is not observed.

There may be some conflict with the new feature..
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-10-3 07:18:11 | All floors
maxx2000 Posted at 2018-10-2 21:50
firmware 2018-09-07-100
The problem with the hang has remained.
1. Run the program.

Your analysis is correct, there are some conflicts in MPG mode.

In MPG mode, if the system is in FRO state, press the start button at this time, FRO will be set to 0, which will cause the maching to be in a pause state (you said the frozen state), at this time you can adjust the FRO by handwheel Value to resume maching.
Reply Support Opposition

Use props Report

0

Threads

6

Posts

40

Credits

Newbie Member

Rank: 1

Credits
40
Posted at 2018-10-9 14:12:11 | All floors
Nikolay81 Posted at 2018-9-26 20:29
I edited the Russian translation. In all the following firmwares, you should use this file.

Спасибо за ваш труд) Возможно ли обновить только файл перевода без обновления прошивки? Для этого в папку install  нужно поместить только файл rus?
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-10-9 17:47:31 | All floors
r6mf49t2 Posted at 2018-10-9 14:12
Спасибо за ваш труд) Возможно ли обновить только файл  ...

yes
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-10-9 17:49:37 | All floors
Ver:2018-10-09-101 Description:
1. On the file and parameter page, you can operate through the handwheel;
2. Increase #2031 uniaxial acc is limited by M_Ctrl start acc;
3. Increase #2030 Soft-limited stop mode;
4. Increase #2029 color reversal;

install(2018-10-09-101).zip

595.69 KB, Down times: 298

Reply Support Opposition

Use props Report

0

Threads

5

Posts

28

Credits

Newbie Member

Rank: 1

Credits
28
Posted at 2018-10-14 14:22:47 | All floors
Could you please increase the maximum halt time for spindle to wait a bit more? 9 seconds is not enough for my spindle to ramp up. Maybe set the limit to something like 20sec to be safe
Regards.
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-10-14 17:12:33 | All floors
You can modify the configuration file.

If your language is English, open eng with Notepad and find this line.
#224 -t1 -s1"Spindle M3/M4/M5 response Duration" -s2"s" -m6 -min=0.000 -max=9.000
Change 9.000 to 20.000, then reinstall eng into the controller
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-10-14 17:14:27 | All floors
Last edited by Nikolay81 In 2018-10-14 17:16 Editor

This has already been written several times. You can increase the maximum value of the parameter through the translation file (eng). And the best option, if you have an asynchronous spindle, is to reduce the spindle stop time in the settings of the inverter. More than 9 seconds is a lot. Even spindles without brakes stop in 3 seconds.
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list