Firmware download - On 6 Page - DDCSV2.1 - Standalone CNC Motion Controller - Digital Dream Technology support
Author: ytliu

Firmware download

[Copy Link]

0

Threads

22

Posts

370

Credits

Intermediate Member

Rank: 3Rank: 3

Credits
370
Posted at 2018-9-21 22:56:35 | All floors
With the latest firmware(2018-09-07-100).zip), the following happens.
Start  program, and hit the FRO button to adjust the feed rate. Controller locked up.  Locked up & could only reboot to clear it.
Reply Support Opposition

Use props Report

0

Threads

26

Posts

1669

Credits

Gold member

Rank: 6Rank: 6

Credits
1669
Posted at 2018-9-22 01:14:57 | All floors
Nikolay81 Posted at 2018-9-21 20:06
Thank you.
Russian translation, now completely finished.
Translated everything that can be translat ...

Nikolay81, не совсем точный перевод параметров #2001-#2003

1.zip

397 Bytes, Down times: 95

Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-9-22 05:37:22 | All floors
maxx2000 Posted at 2018-9-21 22:56
With the latest firmware(2018-09-07-100).zip), the following happens.
Start  program, and hit the FR ...

Hi,maxx2000.

Does this fault occur every time? Is your controller 1.1 or 2.1? Can you send me your setting file?
Reply Support Opposition

Use props Report

8

Threads

333

Posts

1040

Credits

Super Moderator

Rank: 8Rank: 8

Credits
1040
 Author| Posted at 2018-9-22 06:04:25 | All floors
maxx2000 Posted at 2018-9-21 22:56
With the latest firmware(2018-09-07-100).zip), the following happens.
Start  program, and hit the FR ...

I found the reason for this error, because #2028 is a new parameter, after the installation is complete, #2028=0, you need to reset this parameter, such as 10.
Reply Support Opposition

Use props Report

0

Threads

22

Posts

370

Credits

Intermediate Member

Rank: 3Rank: 3

Credits
370
Posted at 2018-9-22 17:20:47 | All floors
I thought this was some kind of inexpensive with new features. Thank you. Everything is working.
Reply Support Opposition

Use props Report

0

Threads

1

Posts

12

Credits

Newbie Member

Rank: 1

Credits
12
Posted at 2018-9-23 00:18:52 | All floors
Last edited by Evgen In 2018-9-23 00:20 Editor

HI everybody! Thanks for support and improving the device!
Is there somebody faced the trouble - in program (AUTO) mode when G0 command starts(for ex. G0 Y1000) Y axis sometimes misses steps and motor stops, however in the manual fast moving mode(CONT) it was never happened.The speed limits are set the same - 2800mm/min and acceleration/stoping also the same - 40mm/sec2 for both manual and program modes. X and Z axis are working normally.
Dear Ytliu, if it possible can you comment these sections of setting(Motor parameters) please !
It may be I did somthing wrong but when I used Mach the CNC worked right.
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-24 23:23:25 | All floors
alexwalex Posted at 2018-9-22 01:14
Nikolay81, не совсем точный перевод параметров #2001-#2003

По-моему, твой перевод тоже немного корявый.
Посмотри новый перевод - так будет лучше?Ещё в переводе есть места, которые можно более понятно назвать, по твоему мнению?

rus.rar

4.79 KB, Down times: 72

Reply Support Opposition

Use props Report

0

Threads

26

Posts

1669

Credits

Gold member

Rank: 6Rank: 6

Credits
1669
Posted at 2018-9-25 02:04:08 | All floors
Nikolay81 Posted at 2018-9-24 23:23
По-моему, твой перевод тоже немного корявый.
Посмотри  ...

Всё OK!
Ну разве только вот:
#218 -t2 -s1"Нажатие старт после паузы" -m16 -min=0.000 -max=1.000 -i0"Продолжить" -i1"Рестарт"
Reply Support Opposition

Use props Report

15

Threads

139

Posts

513

Credits

Senior Member

Rank: 4

Credits
513
Posted at 2018-9-25 19:13:48 | All floors
alexwalex Posted at 2018-9-25 02:04
Всё OK!
Ну разве только вот:
#218 -t2 -s1"Нажатие старт посл ...

Насчёт "всё ОК" - это ты зря. Перевод, довольно корявый. Просто у меня больше нет времени им заниматься.
Я пожилой станочник, в "этих ваших Интернетах" плохо разбираюсь.
А ты - молодой и активный. Может, создашь тему на профильных форумах о улучшении перевода?
Коллективный разум, сможет этот перевод улучшить. Если захочет :-)
Reply Support Opposition

Use props Report

0

Threads

26

Posts

1669

Credits

Gold member

Rank: 6Rank: 6

Credits
1669
Posted at 2018-9-25 19:47:22 | All floors
Корявый??? Ты наверное не видел перевод Fanuk-а - вот это корявый перевод, стыдно должно быть японцам.
Сложно перевести точно и понятно, когда ограничено количество символов. Мне кажется текущей версией перевода вполне можно пользоваться, а кого не устроит - сам сможет подправить под себя.
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list