Firmware download

dexpiste · Posted at 2019-5-11 07:10:45

Last edited by dexpiste In 2019-5-11 07:12 Editor

Edit:

ytliu · Posted at 2018-10-30 15:28:40

Thank you, I will modify it.

maxx2000 · Posted at 2018-10-30 13:52:27

Marked one bug.
In the inverse screen layout, if you press FRO, then choose M5. The entire screen is highlighted.

Nikolay81 · Posted at 2018-10-18 15:56:50

Kev0 Posted at 2018-10-18 14:20
Sorry said it the wrong way. I got a D-100 and there is no manual available.

Why this cant be compe ...

See this instruction. https://cloud.mail.ru/public/Fg71/dw2VRmveu They say that it fits. Judging by the information on the forums - this inverter is buggy. There are a lot of problems with it.

Kev0 · Posted at 2018-10-18 14:20:35

Sorry said it the wrong way. I got a D-100 and there is no manual available.

Why this cant be compensated ? Sure it can.
I set the rampup in DDCSV to 0 wich results in a 0-10V in no time. (Spindle reacts the same way -> ramp slow)
As the spindle runs its ramping curve it just needs more time to reach the desired speed.
In order to have the right cutting speed set the DDCSV to wait a bit longer. Everything is working.

Would be nicer to change the spindle ramping map but this is not possible without a manual .

Nikolay81 · Posted at 2018-10-18 05:37:44

Last edited by Nikolay81 In 2018-10-18 05:56 Editor

Kev0 Posted at 2018-10-18 03:04
@ytliu Thank you very much!
@ Nikolay81 it's not about the braking time. The time to accelerate the ...

This cannot be compensated through DDCSV.
Take a multimeter and see the rise time of the VSO voltage. If it is small, then the reason is in the inverter.Also, it is necessary to connect the VSO input with + 10V in the inverter and see the acceleration time.I attached the instructions to the message. Have you ever looked for it on the Internet?

Kev0 · Posted at 2018-10-18 03:04:04

@ytliu Thank you very much!
@ Nikolay81 it's not about the braking time. The time to accelerate the spindle is to long. I got a NOWFOREVER E-100 but the settings how to set the ramp up time are not described anywhere. For the D-100 there is a manual but the settings regarding to the rampup are different (D-100 is 1-7 /E-100 defalut 400). So I have to compensate this via the DDCSV.

Btw. really great to have such a good support !!

Nikolay81 · Posted at 2018-10-14 17:14:27

Last edited by Nikolay81 In 2018-10-14 17:16 Editor

This has already been written several times. You can increase the maximum value of the parameter through the translation file (eng). And the best option, if you have an asynchronous spindle, is to reduce the spindle stop time in the settings of the inverter. More than 9 seconds is a lot. Even spindles without brakes stop in 3 seconds.

ytliu · Posted at 2018-10-14 17:12:33

You can modify the configuration file.

If your language is English, open eng with Notepad and find this line.
#224 -t1 -s1"Spindle M3/M4/M5 response Duration" -s2"s" -m6 -min=0.000 -max=9.000
Change 9.000 to 20.000, then reinstall eng into the controller

Kev0 · Posted at 2018-10-14 14:22:47

Could you please increase the maximum halt time for spindle to wait a bit more? 9 seconds is not enough for my spindle to ramp up. Maybe set the limit to something like 20sec to be safe
Regards.

Firmware download

View forum before

TEL

0755-87654321