DDCSV1.1-2.1-3.1 firmware information summary

josete72 · Posted at 2020-6-3 02:09:43

Hello
yesterday I received my ddcsv 3.1 controller with the MPG, from the beginning the controller did not see the MPG, and the led of the MPG did not light up either
check the wiring of the MPG and the factory was wrong, the cable from pin 9 (5v gnd) was connected to pin 15 ... fix the problem.connect the MPG to my controller ... and although the led now lights up on the MPG ... my controller does not see it or do anything, it does not move the axes nor does the display show any variation in coordinates
I have thrown to the trash 300 dollars ??
Can somebody help me?
thanks

Joeschi · Posted at 2020-5-12 21:20:55

What ist the latest firmware for DDCSV 1.1? Because I have some troubles with arcs.

Thanks Roger

Adi54 · Posted at 2020-4-10 02:24:42

It searches the DDCSV3.1 pages for new software. Under what principles can the software be downloaded and where can it be found. The factory documentation directs to these pages. Regards. Andrew

Hansi · Posted at 2020-3-16 04:31:38

Hi there:
Just noticed on FB that they were talking about version 2020-03-06-112NOR.
Will it also be available on the forum? I don't use FB.
And is it for V2.1 also?
Thanks
Hansi

ytliu · Posted at 2019-6-6 10:26:22

Last edited by ytliu In 2019-6-6 10:33 Editor

Ver: 2019-06-06-111 Description:
(2019-05-27-111)
1. Increase G93(inverse time feed rate mode) support.
In inverse time feed rate mode, an F word means the move should be completed in one divided by the F number minutes.
For example, if the F number is 2.0, the move should be completed in half a minute.
http://bbs.ddcnc.com/forum.php?m ... tra=page%3D1&page=3
(2019-05-28-111)
2. In the inverse screen layout, correct the problem of displaying when switching to M5;
http://bbs.ddcnc.com/forum.php?m ... tra=page%3D1&page=3
(2019-05-29-111)
3. Add configuration item #2038: Enable the software limit alarm in the idle state;
https://www.facebook.com/groups/ ... k/2858211170862702/
4. Add RESET Hotkey: ctrl+r;
In file editing, add []{} character input;
https://www.facebook.com/groups/ ... k/2860026127347873/
(2019-06-06-111)
5. Improve the specific line start function, display the command line information before starting the machining,
and ask whether to start machining or continue scanning, such as continue scanning, the line increment is specified by #2039;
6. Modify the soft limit mechanism in manual mode to ensure that the motion does not exceed the range of the soft limit. Cancel #2030, #2032-#2035 configuration item;
7. Under the 2nd PROBE function, add mode 3 operation support (executed by X+);
8. When the SJR is switched, the gear position with the JOG distance of 0 will not be filtered out;
9. Add configuration item #2041: G53/G153 function interchange, default G53 is coordinate system selection group command, used to select G53 coordinate system; G153 is motion group command, used for positioning movement under machine coordinate system;

ytliu · Posted at 2019-5-9 23:26:12

This is the latest version.
Ver:2019-05-09-109 Description:
1. Increase the coordinate record macro function;(Pending verification)
http://bbs.ddcnc.com/forum.php?m ... page%3D1&page=2

2. Add the macro function GetCenterPos[]: Find the center of the circle through the 3 points on the circle.
GetCenterPos[x1,y1,x2,y2,x3,y3,n1,n2]
x1, y1 is the x-y coordinate of the first point;
x2, y2 are the x-y coordinates of the second point;
x3, y3 are the x-y coordinates of the third point;
n1 is a variable index storing the X coordinate of the center, for example, n1=4, then #4=x coordinate of the center;
n2 is a variable index storing the Y coordinate of the center, for example, n2=5, then #5=y coordinate of the center;
https://www.facebook.com/groups/ ... k/2823155341034952/

math_indy · Posted at 2019-5-9 22:38:32

I noticed that Ver:2019-05-07-109 has the filename 2018-07-05 (which says 2018 rather that 2019). That makes me worry that it's an older version. Probably just a typo but also shown on nvcnc web page as 2018-07-05:
https://www.nvcnc.net/ddcsv2.1.html

I want to install the latest but the 2018 filename makes me think this version is older than what I am currently running.

Will_D · Posted at 2019-5-7 17:34:36

I've already thanked you on Facebook but again many thanks for this information. It is priceless. Great documentation sells great products.

If you need any help with the user manual please PM me and we will see what I can do.

DDCSV1.1-2.1-3.1 firmware information summary

View forum before

TEL

0755-87654321