Digital Dream Technology support

Title: MPG wheel won't move any axis motor [Print This Page]

Author: GotDiesel Time: 2021-2-16 08:32
Title: MPG wheel won't move any axis motor
All motors work perfectly in CONT mode on keypad. If I change Mode to MPG, no axis moves. No matter what axis motor I choose, the x motor makes noises as I turn wheel, but no movement occurs. I assume it must be in perameters, but I have looked all over and can't seem to find anything that fixes the problem.

Author: Belwect Time: 2021-2-16 17:42
Last edited by Belwect In 2021-2-16 17:58 Editor

For MPG to work, you need 2 power supplies. One for powering the controller, the other for powering the peripheral. You also need to check the wiring of the MPG remote control.

Безымянный.jpg (61.5 KB, Down times: 227)

l7AMp.jpg (51.3 KB, Down times: 237)

Безымянный.jpg (76.61 KB, Down times: 225)

Author: GotDiesel Time: 2021-2-17 02:33
I have two power supplies as shown. Check wiring? It is pre assembled by factory. Are you saying I should open factory plug and check factory wiring?

Author: Belwect Time: 2021-2-17 14:09
Open the plug and the remote control itself, ring the wires.

Author: GotDiesel Time: 2021-2-18 05:23
Last edited by GotDiesel In 2021-2-18 23:50 Editor

The wiring is all wrong inside the MPG. All colors wrong per instructions. All instructions very unclear and very blurry to read. I can't believe we have to rebuild the product to make it work.

On another note. The wiring shows 18 wires to connect to 15 pin connector. My harness only has 17 wires. Many of the colors are not on correct pins and many colors seem to be wire colors picked dont even exist on the wiring code.

This is the worst experience with a new product yet. At least if you expect me to fix your crap, you should supply very clear clean wiring instructions.

Im not sure how Im going to handle this yet, but I will probably keep looking for a better quality controller. At least one that the manufacturer wires per their own instructions.

Author: ShaniaDDream Time: 2021-3-15 11:35
1. Firstly, please check whether you are using two 24 V power supply, one for the system, and one for the I/O power supply. If this is correct, normally, you will see the signal light on the MPG is on when the MPG is connected to the MPG port tightly. 2. Secondly, please check the MPG parameter page , make sure that #432 and #448 choose LOW (standard MPG signal electric level) and CLOSE (MPG control mode). Hope it helps. 3. Also you can use the test page to check the MPG working status, if its value is changing during rotating the MPG handwheel, it means the MPG works well.

Author: dhammer63 Time: 2021-6-15 20:04
agree none of this is helpful , bought this because it came with mpg. no info on rewire , wrong colors , buy another mpg ,or take all apart and return!!!! not happy at all !!

Author: dhammer63 Time: 2021-6-15 20:16
ddcs is not understanding mpg supplied with system is not same color wiring why cant this be resolved. paid more for kit with mpg !! should i just return it refund .

Author: MOHANLAL Time: 2022-1-2 23:54
Hello dear, i read all of your questions, now, my doubt is did you open the MPG HANDWHEEL, sometimes the handwheels come with 4 pins and sometimes it comes with 6 pins and you can see purple and purple/black wire is not connected if it is 4 pins. For a solution opin it and tell me.;
my email is mohanlal317@yahoo.com
Thank you;

Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)