Title: Slave axis [Print This Page] Author: Mikeyd2673 Time: 2020-10-20 19:19 Title: Slave axis Can someone please help me figure out how to slave my A axis to my Y axis on my ddcsv3.1 motion controler ? My Y axis runs 2 stepper motors so I need to slave the A axis to the Y axis. I have the users manual but can't find any information on this subject so if anyone can help me out I would really appreciate it thank you Author: JessyChen Time: 2020-10-20 19:48
You can connect double Y axis to one Y axis terminal of DDCS controller.Both Y drives feed of the Y output of the DDCS. That also works. Author: janthoni Time: 2020-12-31 22:58
I know this is a possibility but having the A drive slaved to the Y would make it possible to home both of them separately to make sure the gantry is square each time you start up. Author: oliver Time: 2021-1-4 04:26
there is no such function in this controller. Need an extra fee to align the portal to Y
We make such boards
When using two motors and two home position sensors, it becomes necessary to control the motors separately. This will allow each motor to respond to the sensor at the origin. This method of returning to the home position ensures that the axes are perpendicular. Some CNC systems have built-in capabilities for implementing such a connection scheme, in other systems there is no such software capability, therefore the this controller is used.
Specifications
The supply voltage of the controller is 12-48 VDC.
Type of connected sensors NPN.NO, NPN.NC (type NO or NC can be switched with jumpers on the board)
Pull signal interruption (5V)
Work algorithm
On power up, the timing controller continuously polls the home position sensors. As soon as one of the sensors is triggered, the controller interrupts the PULL- signal to the driver corresponding to the sensor. Then the second sensor is expected to be triggered, after which the PULL signal to the second driver is interrupted. Thus, both sides of the same axle, but of the two motors, return to their home position. An OUT signal is sent to the controller, which means the sensor is triggered along the axis.
After completing this cycle, it can be repeated during the entire operating time of the controller.
Emergency lock
if one of the sensors is active when power is applied, then the portal along the Y axis is completely blocked, in the status window of the sensors of the machine control system, the status of the sensor along the Y axis flashes, and the OUT LED on the synchronization board flashes;
if both sensors are active during power up, then the portal along the Y axis will be blocked when one of the sensors is triggered again. Author: janthoni Time: 2021-1-5 11:42
I really like this board where would I be able to order this or what is its complete name?Author: Юрий Time: 2021-1-10 03:32
I use 2 ballscrews along the y-axis and two servomotors for the game, I connect two servomotors in parallel to the game axisAuthor: kous Time: 2021-3-19 17:52
There is a connection diagram?Author: Juzer99 Time: 2021-3-21 10:18
Hello, What is the model number of this board and where can I buy them?Author: neilcoppley Time: 2022-10-17 04:21
hello imintrested in this board for my machine can you tell me where to purchase this Author: neilcoppley Time: 2022-10-17 04:23
did you ever get the name of the boardAuthor: DINMS Time: 2022-10-31 22:54 https://wldev.ru/wldaxis/Author: milcho43 Time: 2023-11-13 05:10
the name of this synchronization board is
SEN SYNC v1.3 and v1.3s
Made in china.
Before was $ 30 in Alibaba. It is not available anymore.
I look for it also and saw in Russian site for $ 44
I asked if they ship in USA and I am waiting for an answer.
the name of the site is
cnc-technologi.ru
Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)
