Digital Dream Technology support

Title: Post processor [Print This Page]

Author: nzlowie Time: 2018-7-12 19:54
Title: Post processor
Hi there, I've just powered up my new 2.1 controller and I can't find a post processor that works with it. I use Vcarve pro which has a lot of processors but I can't find one that works properly.

Any idea's please.

Many thanks Dave

Author: 71taa Time: 2018-7-12 23:18
Using F360 with Fanuc postprocessor w/o subprograms, helical movements should be disabled (it's a matter of gcode processing, the controller will use helical movements in the end).

Removing o1001 sub call in the result, and that's all.
https://madmodder.net/index.php/topic,11598.900.html - here is a long discussion, pp's are discussed there as well as controller limitations.

Author: maxx2000 Time: 2018-7-13 23:47
for Mach3 fully supported. edit according to your requirements

Author: yehanv71 Time: 2018-7-14 17:23
Hello

DDCSV 2.1........ any assistance with post processor please, i have tried every one in the Fusion360 list and the controller doesnt run. I used the sample file i got with the controller and it works perfect. It was created on Camotics. Also the code looks very different from what i have compared in fusion posts.

Anyone can assist please, PLEASE????, Pretty please??

YCAM-META-DATA: Filename: /home/jcoffland/projects/camotics/svn/trunk/camotics/examples/cat/tiny_cat_outline.svg

YCAM-META-DATA: Timestamp: 2012-01-27 20:11:57.397792

YCAM-META-DATA: Version: 0.5.1

Author: yehanv71 Time: 2018-7-14 17:30

71taa Posted at 2018-7-12 23:18
Using F360 with Fanuc postprocessor w/o subprograms, helical movements should be disabled (it's a ma ...

Hello 71ta

What is meaning of removing o1001, where is this in the result?

Please guide

Thanks

Author: Lukasz Time: 2018-7-14 23:20
Hello,
Here is a post processor for Vectric Aspire. Maybe it will be helpfull for somebody...

Lukasz

DDCSV_Arc_ATC_mm.zip

1.15 KB, Down times: 2427

Author: 71taa Time: 2018-7-14 23:33

yehanv71 Posted at 2018-7-14 17:30
Hello 71ta

What is meaning of removing o1001, where is this in the result?

Typical workflow:
1. Choose the target setup in CAM module
2. Ensure that operation names doesn't contain symbols that aren't allowed in g-code comments (like parentheses and so on)
3. Select the 'Post Process'
4. Select "FANUC / fanuc" postprocessor
5. Set following properties:
5.1 Allow helical moves - No
5.2 G28 Safe retracts - No (it's a matter of taste)
All other options by default
6. Open the generated file. In the beginning you'll see the following (depends on your setup):
%
O1001
(T1 D=1. CR=0. - ZMIN=-2.5 - FLAT END MILL)
G90 G94 G17 G49 G40 G80
G21
G53 G00 Z0.
7. Remove the 'O1001' line
8. If you haven't setup home switches on your CNC and doesn't use homing sequence before the work - remove G53 lines - both in the beginning and in the end of file - otherwise you could hit limits easily.

That's all. Works for all trajectories I've tested. With custom T.nc (simple M5 M0) manual tool change with probe is working and so on.

And one more thing (see other discussions in this forum) - I'm not using the diameter correction in the controller, using F360 CAM for this.

Author: creisey Time: 2020-2-11 18:57
is there a postprocessor for Fusion 360? or do you just use the Fanuc basic and then later delete some lines?

and is there a postprocessor for rhinocam?

for any straigt forward solution i would be more than thankfull

Author: 71taa Time: 2020-2-12 13:31

fanuc.cps.zip (16.68 KB, Down times: 1425)

Slightly modified fanuc PP.
Helical moves are on (since the old post time I haven't found any problems with it)

Author: creisey Time: 2020-2-12 18:55
another little question, i read in the advertisments of DDCSV3.1 that USB hotplug is not possible. is that also with the DDCSV2.1 the case. or is it anyway a problem?

Author: yehanv71 Time: 2020-2-17 09:09
Hi 71taa

I just finished setting up my DDCSV2.1 4 axis controller and managed to successfully edit a post processor for Autodesk fusion 360 that will be compatible with DDCSV1.1, 2.1 and most probably 3.1. Also there is some adjustment to calibrate the controller to the 4 axis so you can get exact degrees and avoid over or under stepping.

Anyone need further assistance with this can contact me if needed.

Author: Tim Time: 2020-2-20 02:06

yehanv71 Posted at 2020-2-17 09:09
Hi 71taa

I just finished setting up my DDCSV2.1 4 axis controller and managed to successfully edit ...

Hi yehanv71
I am just this afternoon starting to set up my 4th axis on my newly arrived DDCSV2.1
So the settings you used and the fusion Post Processor would be very helpful
thanks for the offer

Tim

Author: Dean Time: 2020-3-28 10:24
Looking through the manual it seems to me that it is a basic RS-274 interpreter. Much like EMC (LinuxCNC)

Author: arm-del-riev Time: 2020-4-5 23:45

yehanv71 Posted at 2020-2-17 09:09
Hi 71taa

I just finished setting up my DDCSV2.1 4 axis controller and managed to successfully edit ...

hi yehanv71
i need f360 pp for mi ddcsv2.1. can you help me?

Author: Jorum67 Time: 2021-9-2 22:25

yehanv71 Posted at 2020-2-17 09:09
Hi 71taa

I just finished setting up my DDCSV2.1 4 axis controller and managed to successfully edit ...

Hi yehanv71
Need also help. But I have the 4th axis enabled.

Author: dmitrijk Time: 2021-11-27 22:19
Autodesk Fusion 360 Fanuc postproccesor work very well with out changes.

https://cam.autodesk.com/hsmposts?p=fanuc

Author: Pobedyst Time: 2022-1-4 22:09
Unfortunately, it does not work with 5 axes, in the case of a free license, 600 dollars a year to pay for a garage machine for a license, so that 5 axes would work is not profitable.

Author: myddcsv Time: 2022-1-31 08:08
My ddcav3.1 is beeping and reset don’t reset
Can someone help me
Thanks

Author: dannymeakins Time: 2022-8-19 16:39
did you ever find an answer to this?

Author: dannymeakins Time: 2022-8-19 16:45
Hi,

i am having problems with a post processor for cut2d pro. Could you please help me.

Author: misael Time: 2022-10-22 23:51
eu estou com o mesmo problema, preciso do pós processador para fazer funcionar um controlar thc para minha mesa de corte a plasma

Author: misael Time: 2022-10-22 23:52
eu estou com o mesmo problema, preciso do pós processador para fazer funcionar um controlar thc para minha mesa de corte a plasma

Author: misael Time: 2022-10-23 00:00
eu estou com o mesmo problema, preciso do pós processador para fazer funcionar um controlar thc para minha mesa de corte a plasma

Author: rob Time: 2023-3-3 04:54
postprocessor aspire ddcs v3.1

Author: softm Time: 2023-10-22 06:01
MasterCam 2018 postprocessor (for Fanu 300 3axis mm) does anybody have this? Please help me got it.

Author: firukkk Time: 2023-11-18 03:38
@Lukasz

Is the DDCSV_ATC_mm post processor you shared compatible with DDCS Expert?

My cnc milling machine does not have ATC, can I still use it?

I am using Aspire 8.5.

Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)