Title: MPG driving the .nc file. [Print This Page] Author: Lindo Time: 2019-4-27 13:52 Title: MPG driving the .nc file. Hello Ytliu.
I watched your facebook video of the MPG running the .nc file.
really fantastic, this feature would be useful when setting up new parts to me machined.
So how do you do this is the question.
Well done my friend.
John
Spain Author: ytliu Time: 2019-4-28 07:49
you need to set the #3 parameter ("Function of tool path key") to 1, and the "TOOL PATH" key will be used to enter or exit the MPG guidance function.Author: Lindo Time: 2019-4-28 13:19
Brilliant
Thanks
JohnAuthor: Lindo Time: 2019-5-14 02:59
ytliu
If I wanted to verify a particular nc type code (programme) looking at each line for line by using the MPG.
What settings on the MPG do I need.
I understand the control will not view the code(programme) IE in reverse but only forwards.
The setting MPG #3 "jog" ? to next line of a code would be very useful when setting up and verifying new programs prior to running using the "RUN" key. less accidents.
I could then alter the through my remote keyboard EDIT the file through the remote keyboard and save back to the USB stick ?
Thanks
John (BARCA) forever
Spain
Author: ytliu Time: 2019-5-14 06:19
If you want to check the nc code line by line, you can use the single step mode (SBK): in the READY state, press the F4 key, the system enters the single step mode, after which the start key is pressed each time. The code executes one line. Press the F4 key after pressing the Pause key and the system will exit the single step mode.
In order to use the above features, you need to connect the usb keyboard.
With the usb keyboard, you can edit the nc code online.Author: Lindo Time: 2019-5-14 13:16
Ytliu
Many thanks, I will try this morning.
Best regards
John
SpainAuthor: Lindo Time: 2019-5-15 01:47
Hello Ytliu.
Using version 2019-03-20-107 NOR
Connected a USB hub to the control USB input, 1 port is a wireless keyboard plug but
at first the control display would not see my USB stick with the NC file.
Just the main files and parameter files.
All scroll and entr functions were OK.
Then changed parameter #120 to 1, then the control was able to see the nc file.
So far no problems.
Now entered the program and it ran it OK under the normal mode cont mode.
Paused the program and I sent the mill back to start all over from the beginning.
Again not a problem.
Pressed reset, entered in the file again, and pressed F4 on the keyboard, this did not work.
I pressed the start button and SBK appeared on the top LH of the screen, by pressing this
it did jump from line to line but stalled after 10 lines, and the control "locked" up. Froze.
I had to power down and power up, not a major issue.
So I tried the F3 to edit, the program lines appeared, but no visible cursor on the screen so
it would not let me edit or scroll.
Running a black background with white numbers letters.
I think I am doing something wrong.
Please help
Thanks
John
Spain
Author: ytliu Time: 2019-5-15 12:49
Ver:2019-05-15-109 Description:
1. Increase the coordinate record macro function;(Pending verification) http://bbs.ddcnc.com/forum.php?m ... tra=page%3D1&page=2
2. Add the macro function GetCenterPos[]: Find the center of the circle through the 3 points on the circle.
GetCenterPos[x1,y1,x2,y2,x3,y3,n1,n2]
x1, y1 is the x-y coordinate of the first point;
x2, y2 are the x-y coordinates of the second point;
x3, y3 are the x-y coordinates of the third point;
n1 is a variable index storing the X coordinate of the center, for example, n1=4, then #4=x coordinate of the center;
n2 is a variable index storing the Y coordinate of the center, for example, n2=5, then #5=y coordinate of the center; https://www.facebook.com/groups/ ... k/2823155341034952/
3. Increase the all-axis return zero function in the machine coordinate system. https://www.facebook.com/groups/ ... k/2826643040686182/
4. In the file page, sort by file name https://www.facebook.com/groups/ ... k/2832029936814159/
5. Change the file editing font and correct the error that the file cannot be edited;
Author: ytliu Time: 2019-5-15 12:53
In addition, in the single-step mode, sometimes there is no response by pressing the start button, I am looking for the cause of the problem.
If this happens, you don't need to turn off the power, you can press the reset button to exit.Author: Lindo Time: 2019-5-15 22:36
Ytliu
New version loaded OK.
F3 cursor and edit functions now OK.
F4 and enter works for about 7 lines and locks up.
SBK visible in the LH top of the screen.
Thanks
John
SpainAuthor: ytliu Time: 2019-5-16 07:14
Ver:2019-05-16-109 Description:
6. Correct the error that the program stops responding in single-step(SBK) mode;
Author: Lindo Time: 2019-5-18 13:23
Not sure if you received my post just sent 18 May 7.15 CET.
Not installed the latest version, still on May 15 th.
Problem with the control not seeing the nc file stick that is inserted into a USB hub, second port of the hub is a remote wifi keyboard dongle.
Without the hub, the USB stick with nc files operates OK.
But with the keyboard attached it does not function, so I cannot use the Functions keys.copy edit files.
I notice you have removed the parameter #120 from the parameter settings, has this been an issue in the past.
Thanks
John
Spain Author: ytliu Time: 2019-5-18 14:27
You can modify the eng file and add the #120 parameter to the param page.
#120 -t2 -s1"U disk partition type" -s2"" -m16 -min=0.000 -max=1.000 -i0"With partition" -i1"No partition"
Or force the #120 parameter to 1.
#120=1 -t2 -s1"U disk partition type" -s2"" -m0 -min=0.000 -max=1.000 -i0"With partition" -i1"No partition"Author: Lindo Time: 2019-6-16 11:25
Good morning Ytliu.
it´s been very difficult to log into this forum recently.
The link http://bbs.ddcnc.com/forum.php?m ... &page=2#pid1065
has a header NOT SECURE .
Fortunately I have managed to LOGIN this time with my name and password.
Any suggestions
Thanks
John
SpainAuthor: ytliu Time: 2019-6-16 18:45
Hi Lindo.
I will feedback your question to the forum administrator.
Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)
