Digital Dream Technology support

Title: DDCSV3.1 software bug fixes [Print This Page]

Author: ytliu Time: 2019-4-25 08:27
Title: DDCSV3.1 software bug fixes
In the DDCSV3.1 system, the #116-#119 parameter (zero signal source select) cannot be saved due to an error in identifying the version number, and they are reset to 0 each time it is restarted.

You can download and install the firmware in the attachment to solve this problem.

install-4axis(2019-04-25-107).zip

601.67 KB, Down times: 1145

install-3axis(2019-04-25-107).zip

601.76 KB, Down times: 1046

Author: Ghost-51 Time: 2019-7-12 03:27
Hi!!!
Tell me, when sending to 0 - Z also goes to 0, how can I turn it off?
Where can I download the previous firmware version?

thank

Author: ytliu Time: 2019-7-12 07:42
Hi,
I do not quite understand. Can you explain further?
Also, which version of firmware do you need? I can upload it to you.

Author: Ghost-51 Time: 2019-7-12 13:08
Installed the latest firmware 4axis (2019-04-25-107)

I do not like that when the team Shift -Y the Z axis also goes to 0
In the first version of the controller this is not, the axis remains at its height

Author: jjae6 Time: 2019-7-12 14:28
Maybe #54 = 0 (disable Z Home Searching function)?

#54 -t2 -s1"Enable Z Home Searching function" -s3"0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"

Author: ytliu Time: 2019-7-12 16:17
I will add a configuration item to select whether the Z-axis is set to zero when all the axis zeros are performed(shift+'Y-'+'Y-').Is that ok?

Author: ytliu Time: 2019-7-12 16:34
If you are talking about the Home operation, set it up as described by jjae6.

Author: Ghost-51 Time: 2019-7-13 13:58
ytliuI will add a configuration item to select whether the Z-axis is set to zero when all the axis zeros are performed(shift+'Y-'+'Y-').Is that ok?

Well that was such a point

Author: ytliu Time: 2019-7-13 16:12
Ver:2019-07-13-111 Description:
1. Add configuration item #2042:whether all-zero op. contains the Z-axis;

install(2019-07-13-111).zip

609.39 KB, Down times: 762

Author: maxx2000 Time: 2019-7-14 00:09
ytliu It fits all controllers or 3.1 only.

Author: Ghost-51 Time: 2019-7-14 00:52
ytliu Ver:2019-07-13-111 Description:
1. Add configuration item #2042:whether all-zero op. contains the Z-axis;

Thank you, have not yet installed.
Is it for 4 axis controller?
It may be better to add a paragraph in the menu and leave it as it was in previous versions (Shift + 2 * -X), is there such an opportunity?

Author: Ghost-51 Time: 2019-7-14 01:43
Del

Author: ytliu Time: 2019-7-14 06:19
The installation package provided on the forum is applicable to DDCSV2.1-3.1.
If your controller is DDCSV1.1 and the firmware version number ends with NOR, you can use the installation package in the forum to upgrade.

DDCS three-axis and four-axis applications are the same, and it automatically recognizes hardware information.However, their configuration files (eng,chs,rus) are different. The firmware installation package on the forum uses a 4-axis configuration file, so there is no problem installing it on a three-axis controller.

Author: ytliu Time: 2019-7-14 10:32
When #2042=1, this firmware will pop up a dialog window during all zero operation.

install(2019-07-13-111).zip

609.75 KB, Down times: 584

Author: Ghost-51 Time: 2019-7-14 11:44
Thank you, we will install and proto-process on Monday

Author: Ghost-51 Time: 2019-7-16 01:54
Last edited by Ghost-51 In 2019-7-16 02:13 Editor

Install the firmware, # 2042 = 1 или 0, Z axis goes to 0Video https://yadi.sk/i/zWj8n7tO_fLS-Q

Author: ytliu Time: 2019-7-16 05:38
I'm sorry, I misunderstood.I have modified the relevant part in slib.nc, please install it.

install.zip

2.04 KB, Down times: 617

Author: Ghost-51 Time: 2019-7-23 01:54
Last edited by Ghost-51 In 2019-7-23 01:56 Editor

Thanks, it works as it should.But there are bugs, I will observe - I will unsubscribe

Author: bolek Time: 2021-5-7 08:08
Hello all, I have ddcsv2.1 but on-screen say ddcs3v2.1 .I have it unused for a while. The old cutting toy went to the garbage because of the worn and parallel port. I made a new frame and decide to use ddcsv. All works great but don't have all limit switches I use a proximity sw. Working on the proper motor setup I decided to test run circle. Now I see every time the tool gets to the beginning of the circle the machine stop and waits for the controller to catch up. I try different G codes and screw with configuration. Now I know that I have to download G codes into ddcsv. The problem is that I don't have the imperial measurement, no more, only metric. No matter if I change it in config it shaw in. but the value is in mm.
What did I do, help, please

Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)