DDCS3.1 how to connect to Gecko drive - DDCSV3.1 Standalone CNC Motion Controller - Digital Dream Technology support
View: 19585|Reply: 8
Print Previous Topic Next Topic

DDCS3.1 how to connect to Gecko drive

[Copy Link]

5

Threads

17

Posts

69

Credits

Registered member

Rank: 2

Credits
69
Jump to the specified floor
Landlord
Posted at 2020-3-22 04:48:14 | Only Author |Only larger image Replies reward |Descending browser |Read mode
How do I connect DDCS3.1 controller to Gecko drives?    See attached image of Gecko with pinout.


Machine presently wired with common +5V connection to all drives on each axis.  Step and direction assume a grounding pulse.

DDCS3.1 manual state pulse and direction are "differential" +- 5V.  
Reply

Use props Report

5

Threads

17

Posts

69

Credits

Registered member

Rank: 2

Credits
69
recommend
 Author| Posted at 2020-3-25 05:28:54 | Only Author
I decided to use two quad differential line receiver SN75173  to convert step and dir signals from DDCS3.1 unit to work with Gecko step drivers
Wish me luck...  I will report here if success.

Administrator - Please add DDCS3.1 separate forum and move this topic there to help others.

我决定使用两个四路差分线接收器SN75173来转换来自DDCS3.1单元的步进和dir信号,以与Gecko步进驱动器一起使用
祝我好运...如果成功,我将在这里报告。

管理员-请添加DDCS3.1单独的论坛,并将本主题移至其他论坛以帮助他人。
Reply Support 0 Opposition 1

Use props Report

5

Threads

17

Posts

69

Credits

Registered member

Rank: 2

Credits
69
recommend
 Author| Posted at 2020-3-30 01:47:54 | Only Author
Success.  I put two SN75173 on a small perf board.   I ran each axis +-STEP +-DIR signals from DDCSV3.1 to differential inputs.
This provided a +5 to to ground output that is compliant with the Gecko drives.
This board runs on a separate 5v supply.  5v from this supply also went out to each Gecko driver board on the machine (pre-existing wiring I did not want to change). The supply shares the same ground COM- for I/O on the DDCS.   


成功。 我在一个小的穿孔板上放了两个SN75173。 我将每个轴的+ -STEP + -DIR信号从DDCSV3.1运行到差分输入。
这提供了与Gecko驱动器兼容的+5接地输出。
该开发板在单独的5v电源上运行。 来自此电源的5v电压也传到了机器上的每个Gecko驱动器板上(我不想更改的已有接线)。 电源在DDCS上共享用于I / O的相同地面COM-。
Reply Support 1 Opposition 0

Use props Report

5

Threads

17

Posts

69

Credits

Registered member

Rank: 2

Credits
69
Sofa
 Author| Posted at 2020-3-22 04:49:21 | Only Author
Reply Support Opposition

Use props Report

5

Threads

17

Posts

69

Credits

Registered member

Rank: 2

Credits
69
Bench
 Author| Posted at 2020-3-22 04:49:55 | Only Author
Image is here...https://ibb.co/H4CY243
Reply Support Opposition

Use props Report

0

Threads

1

Posts

4

Credits

Newbie Member

Rank: 1

Credits
4
6#
Posted at 2021-9-15 05:25:17 | Only Author
Hello Dean, I would like to know if you would like to give me ease on connecting my Gecko G251x Drivers with the DDCSV3.1.
thank you so much

Fred
Reply Support Opposition

Use props Report

4

Threads

7

Posts

40

Credits

Newbie Member

Rank: 1

Credits
40
7#
Posted at 2022-4-1 00:07:14 | Only Author
I have used the line receiver SN75157P and it works fine. See drawing

Lijn_converter.jpg (968.45 KB, Down times: 686)

Lijn_converter.jpg
Reply Support Opposition

Use props Report

0

Threads

3

Posts

10

Credits

Newbie Member

Rank: 1

Credits
10
8#
Posted at 2024-4-24 22:46:54 | Only Author
If you're in need of some extra excitement or looking for ways to make money, consider visiting 22 AUD Casino login - https://22audcasino.com/ in Australia. With its diverse range of games and easy access, it's a great option to relax and try your luck. Experience the fun and potential rewards at 22 AUD Casino!
Reply Support Opposition

Use props Report

0

Threads

7

Posts

18

Credits

Newbie Member

Rank: 1

Credits
18
9#
Posted at 2024-6-20 21:43:47 | Only Author
Thanks for sharing that information. Keep posting! cash for junk cars revere
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list