Bom dia! So novo por aqui alquem me ajuda - DDCSV3.1 Standalone CNC Motion Controller - Digital Dream Technology support
View: 4321|Reply: 4
Print Previous Topic Next Topic

Bom dia! So novo por aqui alquem me ajuda

[Copy Link]

2

Threads

4

Posts

26

Credits

Newbie Member

Rank: 1

Credits
26
Jump to the specified floor
Landlord
Posted at 2020-11-4 19:31:20 | Only Author Replies reward |Descending browser |Read mode
Bom dia! Eu comprei um controlador DDCS V3.1 V3 fiz as configurações dos eixos X Y Z Mais o quarto eixo "A" não consigo configurar as suas configuracão MOTOR DE PASSO NEME 23 1.8 ANGULO 15 KGF
Good Morning! I bought a DDCS controller V3.1 V3 I made the configurations of the X Y Z axes Plus the fourth axis "A" I can't configure your configurations STEP MOTOR NEME 23 1.8 ANGLE 15 KGF
Reply

Use props Report

0

Threads

23

Posts

80

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
80
Sofa
Posted at 2020-11-4 23:14:25 | Only Author
Dear Israel. DDCS V3.1 is a motion controller, it generate signals to stepper/servo drivers, then drivers Amplify the signal to motors, then the motor knows how to work. Now you still need a driver. Nema 23 1.8 angle motor, you need a 2-4A, and 20-50VDC stepper driver. Good luck to you.
Reply Support Opposition

Use props Report

2

Threads

4

Posts

26

Credits

Newbie Member

Rank: 1

Credits
26
Bench
 Author| Posted at 2020-11-8 03:45:34 | Only Author
A questão e como configura o quarto eixo na controladora DDCS V3.1 The question and how to configure the fourth axis on the DDCS V3.1 controller
Reply Support Opposition

Use props Report

0

Threads

23

Posts

80

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
80
Floor
Posted at 2020-11-17 21:17:33 | Only Author
The configuration methods on A axis, just same as other axis. Signal is PUL + DIR ; the difference it that A is a Rotation axis.There are parameters in Para page about A axis, you can set. One point about it is that you should set the rotation direction properly in your toolpath software.
Reply Support Opposition

Use props Report

1

Threads

8

Posts

31

Credits

Newbie Member

Rank: 1

Credits
31
5#
Posted at 2021-11-1 04:36:19 | Only Author
fala blz,  Cara voce consegue tirar umas fotos dos componentes da sua controladora,  tirando a tampa trazeira e fotografando a placa bem detalhada,?.. Comprei uma dessa e liguei direto na tomada , sem passar por  uma fonte de 24 v, e ai ja viu ne.. queimou antes mesmo de eu testar..  mandei arrumar, poresm os caras tiraram uns componentes nela, e disseram que nao ha mais como consertar. entao quer ver com alguem q tenha essa controladora, pra fotografar os componentes dessa controladora,  para que eu possar estar comprando  os componentes e efetuando a troca .
Reply Support Opposition

Use props Report

You need to log in before you can reply Login | Register now

This forum Credits Rules

Shenzhen Digital Dream Numerical Technology Co., Ltd. support
Adress:507,A Building,Leibo Industry Zone,No. 22 Jinxiu East Road,Kengzi Street,Pingshan district,Shenzhen City,P.R. of China
Phone:13244704799
E-mail:info@ddcnc.com

TEL

0755-87654321

Wchat

Website designed by DigitalDream Technology Support
Quick Reply Back to top Back to list