Please help me with the setup. I need to adjust the 4 axis to operate ...

arco

Hello. Please help me with the setup. I need to adjust the 4 axis to operate the tangential knife. upon command:

1. %
   
2. (Header)
   
3. (Generated by gcodetools from Inkscape.)
   
4. (Using default header. To add your own header create file "header" in the output dir.)
   
5. M3
   
6. (Header end.)
   
7. G21 (All units in mm)
   
8. 
   
9. (Start cutting path id: path4669)
   
10. (Change tool to Tangent knife)
    
11. 
    
12. G00 Z 5.0000
    
13. G00 X 28.2699 Y 28.2364
    
14. 
    
15. G01 A 8.3991
    
16. G01 Z -1.0000 F 300.0000(Penetrate)
    
17. G02 X 29.0256 Y 28.6669 Z -1.0000 I 0.5324 J -0.0560 F 400.0000 A -2.4652
    
18. G01 A -2.4652
    
19. G02 X 29.6163 Y 28.0946 Z -1.0000 I -0.5154 J -1.1231 A -6.3527
    
20. G01 A -6.3527
    
21. G02 X 29.4108 Y 26.3896 Z -1.0000 I -1.3983 J -0.6963 A -13.0221
    
22. G01 A -13.0221
    
23. G02 X 27.9864 Y 25.5434 Z -1.0000 I -1.9364 J 1.6376 A -16.8353
    
24. G01 A -16.8352
    
25. G02 X 25.3987 Y 26.2847 Z -1.0000 I -0.5858 J 2.8420 A -22.3620
    
26. G01 A -22.3620
    
27. G02 X 24.2304 Y 28.6616 Z -1.0000 I 2.6451 J 2.7758 A -26.4028
    
28. G01 A -26.4028
    
29. G02 X 25.4829 Y 32.1459 Z -1.0000 I 4.2392 J 0.4434 A -31.5515
    
30. G01 A -31.5515
    
31. G02 X 28.8368 Y 33.6223 Z -1.0000 I 3.6280 J -3.6938 A -35.6966
    
32. G01 A -35.6966
    
33. G02 X 33.2236 Y 31.8664 Z -1.0000 I 0.2976 J -5.6143 A -40.6664
    
34. G01 A -40.6664
    
35. G02 X 35.0023 Y 27.5277 Z -1.0000 I -4.7489 J -4.4808 A -44.8753
    
36. G01 A -44.8753
    
37. G02 X 32.7463 Y 22.2357 Z -1.0000 I -6.9787 J -0.1519 A -49.7423
    
38. G01 A -49.7423
    
39. G02 X 27.4194 Y 20.1575 Z -1.0000 I -5.3334 J 5.8047 A -53.9953
    
40. G01 A -53.9953
    
41. G02 X 21.2206 Y 22.9117 Z -1.0000 I -0.0068 J 8.3375 A -58.7960
    
42. G01 A -58.7960
    
43. G02 X 18.8445 Y 29.2285 Z -1.0000 I 6.8603 J 6.1858 A -63.0813
    
44. G01 A -63.0813
    
45. G02 X 22.0959 Y 36.3352 Z -1.0000 I 9.6926 J -0.1375 A -67.8358
    
46. G01 A -67.8358
    
47. G02 X 29.4037 Y 39.0082 Z -1.0000 I 7.0381 J -7.9155 A -72.1459
    
48. G01 A -72.1459
    
49. G02 X 37.4189 Y 35.2601 Z -1.0000 I -0.2814 J -11.0457 A -76.8665
    
50. G01 A -76.8665
    
51. G02 X 40.3882 Y 26.9608 Z -1.0000 I -8.9701 J -7.8902 A -81.1963
    
52. G01 A -81.1963
    
53. G02 X 36.1439 Y 18.0367 Z -1.0000 I -12.3974 J 0.4249 A -85.8909
    
54. G01 A -85.8909
    
55. G02 X 26.8525 Y 14.7715 Z -1.0000 I -8.7422 J 10.0245 A -90.2367
    
56. G01 A -90.2367
    
57. G02 X 17.0193 Y 19.5117 Z -1.0000 I 0.5681 J 13.7479 A -94.9107
    
58. G01 A -94.9107
    
59. G02 X 13.4585 Y 29.7955 Z -1.0000 I 11.0785 J 9.5943 A -99.2697
    
60. G01 A -99.2697
    
61. G02 X 18.6943 Y 40.5381 Z -1.0000 I 15.0978 J -0.7111 A -103.9271
    
62. G01 A -103.9271
    
63. G02 X 29.9707 Y 44.3942 Z -1.0000 I 10.4462 J -12.1323 A -108.2973
    
64. G00 Z 5.0000
    
65. 
    
66. (End cutting path id: path4669)

Copy the code

(Footer)M5G00 X0.0000 Y0.0000M2(Using default footer. To add your own footer create file "footer" in the output dir.)(end)%The "X", "Y", "A" axis moves, but it does not run at the same time. First, "X-Y", then "A". What's wrong with the settings?

ytliu

Ver:2018-01-21-91 amendments:
1. Addition of "circular centrifugal acceleration" configuration
2. Add A axis command control under soft arc algorithm