Digital Dream Technology support

Title: Visualization [Print This Page]

Author: Сергей Time: 2018-11-1 02:52
Title: Visualization
Hello. I have this question. Maybe someone knows how to fix, when rendering a zero point in the middle of the screen. And the display of processing starts from it and goes beyond the border of the screen. Is it possible to fix it and scale down. In other controllers (on the PC) everything is displayed correctly.

Author: Сергей Time: 2018-11-1 02:55
[img]http://www.cnc-club.ru/forum/download/file.php?id=149587&mode=view&mt=1

[/img]

Author: ytliu Time: 2018-11-1 14:46
Can you upload your Gcode? The photo shows that your GCode works in the G59 coordinate system. Does your Gcode use multiple workpiece coordinate systems?

Author: Сергей Time: 2018-11-3 03:18
T1M6
G0Z5.000
G0X0.000Y0.000S10000M3
G0X29.659Y2.225Z5.000
G1Z0.842F420.0
G1X25.714Z0.147
G1X25.171Z0.077
G1X23.830Z-0.186
G1X13.532Z-2.003
G1X12.992Z-2.076
G1X11.944Z-2.270
G1X6.233Z-3.300
G1X3.796Z-3.747
G1X3.607Z-3.786
G1X3.419Z-4.031
G1X3.324Z-4.267
G1X3.172Z-5.183
G1X3.041Z-6.375
G1X3.041Y2.225Z-6.375F420.0
G1X3.172Z-5.363F1200.0
X3.324Z-4.587
X3.419Z-4.389
X3.607Z-4.192
X3.796Z-4.186
X6.233Z-4.169
X11.944Z-4.146
X12.992Z-4.137
X13.532Z-4.159
X23.830Z-4.158
X25.171Z-4.131
X25.714Z-4.157
X31.365Z-4.158
X31.527Z-4.151
X31.637Z-4.112
X31.885Z-4.081
X32.288Z-4.199
X32.421Z-4.200
X44.102Z-4.201
X44.238Z-4.190
X44.373Z-4.148
X45.178Z-4.133
X45.717Z-4.166
X45.984Z-4.203
X46.224Z-4.205
X47.178Z-4.139
X47.723Z-4.137
X48.265Z-4.202
X67.759Z-4.200
X68.030Z-4.193
X68.807Z-4.133
X69.332Z-4.130
X69.735Z-4.196
X69.866Z-4.199
X89.153Z-4.202
X89.695Z-4.182
X90.216Z-4.135
X90.746Z-4.132
X91.279Z-4.196
X92.915Z-4.202
X110.844
X111.116Z-4.197
X111.384Z-4.157
X112.099Z-4.129
X112.370Z-4.130
X112.908Z-4.201
X132.398Z-4.199
X133.441Z-4.131
X133.967Z-4.135
X134.237Z-4.187
X134.641Z-4.200
X153.909Z-4.198
X154.443Z-4.166
X154.680Z-4.137
X155.444Z-4.131
X155.981Z-4.197
X167.390Z-4.199
X167.662Z-4.197
X167.939Z-4.108
X168.204Z-4.090
X168.607Z-4.156
X175.070Z-4.160
G0Z5.000
G0X169.643Y2.375
G1Z1.024F420.0
G1X175.953Z-0.089
G1X176.909Z-0.218
G1X177.587Z-0.337
G1X177.849Z-0.417
G1X178.120Z-0.473
G1X188.438Z-2.290
G1X189.793Z-2.482
G1X190.305Z-2.624
G1X195.202Z-3.500
G1X196.446Z-3.734
G1X196.635Z-3.844
G1X196.824Z-4.071
G1X196.872Z-4.265
G1X197.014Z-5.326
G1X197.014Y2.375Z-5.326F420.0
G1X196.872Z-4.426F1200.0
X196.824Z-4.261
X196.635Z-4.081
X196.446Z-4.007
X195.202Z-3.992
X190.305Z-3.979
X189.793Z-3.928
X188.438Z-3.975
X178.120Z-3.978
X177.849Z-3.970
X177.587Z-3.936
X176.909Z-3.937
X175.953Z-3.976
X168.666Z-3.976
X168.363Z-3.915
X168.091Z-3.901

Author: ytliu Time: 2018-11-3 17:47
Sorry, because the DDCSV processor has limited speed and there is no input device such as a mouse, the system cannot browse the track details, so you don't need to compare it with the PC.

Author: ytliu Time: 2018-11-3 18:10
For this GCode, what do you think should be drawn?

Author: Сергей Time: 2018-11-4 01:26

Hello. this is only 1/100 part of G coda / could not load the entire file

Author: Сергей Time: 2018-11-4 01:31

I understand that this is not a computer. I asked how to set 0 point in the lower left corner? To display the image completely

Author: ytliu Time: 2018-11-5 15:53
The display of the image is adaptive. After the system runs GCode for the first time, it will record the length, width and height of the tool path. When it is run again, the system will map it to the artboard according to the principle of maximization. Therefore, the position of the zero point on the artboard is not fixed, but related to the running GCode.

Author: ytliu Time: 2018-11-5 17:44
This installation package allows you to customize the artboard. You need to set #2036 to 1, and then configure the artboard related parameters (#18-#20, #192-#194) according to your actual situation.

The pixels of the artboard are 267*194. It is recommended that you configure the length and height of the artboard in this proportion.

install(2018-11-05-105).zip

597.48 KB, Down times: 1878

Author: ytliu Time: 2018-11-5 17:47
If you want to position the zero point in the lower left corner, set #192 and #193 to 0.

Author: Сергей Time: 2018-11-6 03:43

thank. I'll try to figure it out

Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)