Title: Firmware 2020-03-06-112 bugs [Print This Page] Author: Robchiks Time: 2021-2-26 17:50 Title: Firmware 2020-03-06-112 bugs Last edited by Robchiks In 2021-2-26 17:52 Editor
Wrong direction of hominhg on Z axis #66 !
Wrong polarity of Probe signal electrical level #70 !Author: ShaniaDDream Time: 2021-3-15 15:32
I have checked on version 2020-03-06-112, they are correct, please check your wiring and configuration in the system.
Take our installation of proximity sensor position for Z axis for example, we have installed it at the Z + moving direction. Since the "Home signal " I chose as "limit signal" , then I need to configure all below first as below.
(1)#50 Home signal Effective when HOME value= Ignore HOME
(2)#51 Enable Limit signal when "HOME" Value=Enable
(3)#118 Z-axis zero signal source select Value= Z++ limit signal ( this is according to your installation)
(4)#Z axis Home direction Value=Positive ( this is according to your installation)
Also you need to check below parameters of Z axis to ensure your moving direction correctly
(1) Z axis DIR signal Electric Level value= High
(2) Z axis Pulse signal Electric Level value= High
For Probe signal electrical level #70 , please choose 0= low.
And make sure your wiring is correct, the Probe pin is connected with "+"( red lead), and COM pin is connected with "-"(black lead).If you use this kind probe tool, you can try it this way, hope it helps.
Author: Robchiks Time: 2021-3-22 19:01 Last edited by Robchiks In 2021-3-22 19:12 Editor
1.
it doesn't matter.
when start homing motor goes "down" and after houming motors go "down" too
but on display when you start houming coordinats goes "down" but after goes "up".
Houming work only when (1)#50 Home signal Effective when HOME value= continue HOME
(3)#118 Z-axis zero signal source select - I use Z Home
2.
"For Probe signal electrical level #70 , please choose 0= low.
And make sure your wiring is correct, the Probe pin is connected with "+"( red lead), and COM pin is connected with "-"(black lead).If you use this kind probe tool, you can try it this way, hope it helps."
it dosn't metter too
Your monitor under "toolpath"indicate on touch Probe "HI" but probe work when in #70 set on "LOW"
do you readme ? Author: ShaniaDDream Time: 2021-3-23 18:01
Houming work only when (1)#50 Home signal Effective when HOME value= continue HOME
(3)#118 Z-axis zero signal source select - I use Z Home
--- so you wired the pin" Z home" right? If not check your wiring first.Author: Robchiks Time: 2021-3-24 00:37
yes I use "Z Home" and it wired on ZHome
so and how it affects the direction of rotation of the motor ?Author: ShaniaDDream Time: 2021-3-25 13:48
If you wired "z Home" on the Terminal block, you need to use the "home signal source" , because when you installed a proximity sensor on your engraving machine, this sensor share the "limit signal" and "home signal", that is why you need to configure it in the controller. First , you need to make sure which signal definition pin you are wising and then make it consistent with the one you set the parameters in the controller. Second, you need to disable limit signal when you choose home signal as you wire "z home" ,here "home" is the home signal. If your direction of rotation of the motor is wrong, you can check the either the electric level and direction electric level value for Z axis, if it is not here. You need to check your motors, it has 4 lead inside, two for pulse, and two for direction. When you use the direction to replace pulse. It is better to check from the start. Just for your information. If you are not sure, share your picture here.Author: Robchiks Time: 2021-4-16 16:59 Last edited by Robchiks In 2021-4-16 17:01 Editor
On controller screen under "toolpath"indicate on touch Probe "HI" but probe work when in #70 set on "LOW" ?
Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)