Title: Please help me with the setup. I need to adjust the 4 axis to operate ... [Print This Page] Author: arco Time: 2018-2-9 08:13 Title: Please help me with the setup. I need to adjust the 4 axis to operate ... Last edited by arco In 2018-2-9 08:14 Editor
Hello. Please help me with the setup. I need to adjust the 4 axis to operate the tangential knife. upon command:
%
(Header)
(Generated by gcodetools from Inkscape.)
(Using default header. To add your own header create file "header" in the output dir.)
M3
(Header end.)
G21 (All units in mm)
(Start cutting path id: path4669)
(Change tool to Tangent knife)
G00 Z 5.0000
G00 X 28.2699 Y 28.2364
G01 A 8.3991
G01 Z -1.0000 F 300.0000(Penetrate)
G02 X 29.0256 Y 28.6669 Z -1.0000 I 0.5324 J -0.0560 F 400.0000 A -2.4652
G01 A -2.4652
G02 X 29.6163 Y 28.0946 Z -1.0000 I -0.5154 J -1.1231 A -6.3527
G01 A -6.3527
G02 X 29.4108 Y 26.3896 Z -1.0000 I -1.3983 J -0.6963 A -13.0221
G01 A -13.0221
G02 X 27.9864 Y 25.5434 Z -1.0000 I -1.9364 J 1.6376 A -16.8353
G01 A -16.8352
G02 X 25.3987 Y 26.2847 Z -1.0000 I -0.5858 J 2.8420 A -22.3620
G01 A -22.3620
G02 X 24.2304 Y 28.6616 Z -1.0000 I 2.6451 J 2.7758 A -26.4028
G01 A -26.4028
G02 X 25.4829 Y 32.1459 Z -1.0000 I 4.2392 J 0.4434 A -31.5515
G01 A -31.5515
G02 X 28.8368 Y 33.6223 Z -1.0000 I 3.6280 J -3.6938 A -35.6966
G01 A -35.6966
G02 X 33.2236 Y 31.8664 Z -1.0000 I 0.2976 J -5.6143 A -40.6664
G01 A -40.6664
G02 X 35.0023 Y 27.5277 Z -1.0000 I -4.7489 J -4.4808 A -44.8753
G01 A -44.8753
G02 X 32.7463 Y 22.2357 Z -1.0000 I -6.9787 J -0.1519 A -49.7423
G01 A -49.7423
G02 X 27.4194 Y 20.1575 Z -1.0000 I -5.3334 J 5.8047 A -53.9953
G01 A -53.9953
G02 X 21.2206 Y 22.9117 Z -1.0000 I -0.0068 J 8.3375 A -58.7960
G01 A -58.7960
G02 X 18.8445 Y 29.2285 Z -1.0000 I 6.8603 J 6.1858 A -63.0813
G01 A -63.0813
G02 X 22.0959 Y 36.3352 Z -1.0000 I 9.6926 J -0.1375 A -67.8358
G01 A -67.8358
G02 X 29.4037 Y 39.0082 Z -1.0000 I 7.0381 J -7.9155 A -72.1459
G01 A -72.1459
G02 X 37.4189 Y 35.2601 Z -1.0000 I -0.2814 J -11.0457 A -76.8665
G01 A -76.8665
G02 X 40.3882 Y 26.9608 Z -1.0000 I -8.9701 J -7.8902 A -81.1963
G01 A -81.1963
G02 X 36.1439 Y 18.0367 Z -1.0000 I -12.3974 J 0.4249 A -85.8909
G01 A -85.8909
G02 X 26.8525 Y 14.7715 Z -1.0000 I -8.7422 J 10.0245 A -90.2367
G01 A -90.2367
G02 X 17.0193 Y 19.5117 Z -1.0000 I 0.5681 J 13.7479 A -94.9107
G01 A -94.9107
G02 X 13.4585 Y 29.7955 Z -1.0000 I 11.0785 J 9.5943 A -99.2697
G01 A -99.2697
G02 X 18.6943 Y 40.5381 Z -1.0000 I 15.0978 J -0.7111 A -103.9271
G01 A -103.9271
G02 X 29.9707 Y 44.3942 Z -1.0000 I 10.4462 J -12.1323 A -108.2973
G00 Z 5.0000
(End cutting path id: path4669)
Copy the code
(Footer)M5G00 X0.0000 Y0.0000M2(Using default footer. To add your own footer create file "footer" in the output dir.)(end)%The "X", "Y", "A" axis moves, but it does not run at the same time. First, "X-Y", then "A". What's wrong with the settings?Author: ytliu Time: 2018-2-10 07:39
Ver:2018-01-21-91 amendments:
1. Addition of "circular centrifugal acceleration" configuration
2. Add A axis command control under soft arc algorithm
