Digital Dream Technology support

Title: Drilling, axis A problem [Print This Page]

Author: LUCID Time: 2019-5-20 15:25
Title: Drilling, axis A problem
Hi

Axis A does not execute g-code
display all the time shows 0 axis A

%
(GRAWEROWANIE NAPISU)

(CREATED 05/20/2019 09:15:19)

(#9 - T9 CHAMFER D 3MM )

N1
G54
(T9 CHAMFER D 3MM)
M8
M69
G98 G18 M45
G0 G28 H0
()
G50 S500
(T9 CHAMFER D 3MM)
G0 T0909
G97 S3000 M3
G0 X27 Z1.1
G81 X14 A3.6Z-0.2 R1.9P500 F95
A7.2
A10.8
A14.4
A18
A21.6
A25.2
A28.8
A32.4
A36
A39.6
A43.2
A46.8
A50.4
A54
A57.6
A61.2
A64.8
A68.4
A72
A75.6
A79.2
A82.8
A86.4
A90
A93.6
A97.2
A100.8
A104.4
A108
A111.6
A115.2
A118.8
A122.4
A126
A129.6
A133.2
A136.8
A140.4
A144
A147.6
A151.2
A154.8
A158.4
A162
A165.6
A169.2
A172.8
A176.4
A180
A183.6
A187.2
A190.8
A194.4
A198
A201.6
A205.2
A208.8
A212.4
A216
A219.6
A223.2
A226.8
A230.4
A234
A237.6
A241.2
A244.8
A248.4
A252
A255.6
A259.2
A262.8
A266.4
A270
A273.6
A277.2
A280.8
A284.4
A288
A291.6
A295.2
A298.8
A302.4
A306
A309.6
A313.2
A316.8
A320.4
A324
A327.6
A331.2
A334.8
A338.4
A342
A345.6
A349.2
A352.8
A356.4
A0
G80
G0 X27 Z1.1
G53 X0 Z0
M1
M5
M9
M46
M30
%

What's wrong with g-code?

Author: edelec Time: 2019-5-20 16:00
There is no A position option in G81. I suggest you make your A move then run G81 as a subroutine

Author: ytliu Time: 2019-5-20 16:09
As edelec said, the G81 command in the current motion library(slib.nc) does not parse the A axis.The attached slib.nc adds A-axis parsing, try it out.

install.zip

2.05 KB, Down times: 786

Author: LUCID Time: 2019-5-20 16:42
Last edited by LUCID In 2019-5-20 16:54 Editor

Thank you very much guys !
file from ytliu solved the problem!
I struggled the whole weekend

The machine is now working perfectly

Author: LUCID Time: 2019-5-21 01:27
Last edited by LUCID In 2019-5-21 02:16 Editor

Axis-A does not work, however, with G83

%
(GRAWEROWANIE NAPISU)

(CREATED 05/20/2019 18:55:03)

(#7 - T7 DRILL D 1MM )

M8
G98 G18 M45
G0 G28 H0
G50 S0
G0 T0707
G97 S9549 M13
G0 X27 Z2
G83 X14 A18Z-0.382 R0P500 Q0.5 F50
A36Q0.5
A54Q0.5
A72Q0.5
A90Q0.5
A108Q0.5
A126Q0.5
A144Q0.5
A162Q0.5
A180Q0.5
A198Q0.5
A216Q0.5
A234Q0.5
A252Q0.5
A270Q0.5
A288Q0.5
A306Q0.5
A324Q0.5
A342Q0.5
A0Q0.5
G80
G0 X27 Z2
G0 A0 Z60
M1
M5
M9
M46
M30
%

Can you help?

Author: ytliu Time: 2019-5-21 06:05
All drilling instructions(G73,G81,G82,G83) have been modified.

install.zip

2.04 KB, Down times: 752

Author: LUCID Time: 2019-5-21 13:27
Thank you again for help

very good job ytliu
I'm happy because the machine works perfectly

I cordially greet !

Author: ytliu Time: 2019-5-21 13:29
slib.nc in the firmware supports fixing drilling cycles on axis A (G73, G81, G82, G83).

Welcome Digital Dream Technology support (http://bbs.ddcnc.com/)